40t钢包底吹特征的水力学模拟研究

特殊钢 ›› 2020, Vol. 41 ›› Issue (5): 14-18.

40t钢包底吹特征的水力学模拟研究

欧修龙¹，王乐² ，王绍明¹，王国强¹

1汉江师范学院物理与电子工程学院，十堰442000；
2钢铁研究总院，北京100081

收稿日期:2020-05-20 出版日期:2020-10-01 发布日期:2022-05-05
作者简介:欧修龙( 1980-),男，博士(2018年钢铁研究总院)，讲师， 2004年三峡大学(本科)毕业，金属材料研究。

Research on Characteristics of 40 t Ladle Bottom Gas Blowing Process by Water Modeling

Ou Xiulong¹, Wang Le² , Wang Shaoming¹ ， Wang Guoqiang¹

1 School of Physics and Electronic Engineering, Hanjiang Normal University, Shiyan 442000；
2 Central Iron and Steel Research Institute, Beijing 100081

Received:2020-05-20 Published:2020-10-01 Online:2022-05-05

摘要/Abstract

摘要： 以钢厂40t LF为原型,应用广义相似理论进行1:3水力学模拟实验研究。根据白金汉π定律,得到描述底吹氩钢包内钢液混合效果的特征数方程模型。通过对实验数据回归分析,得出几何相似的钢包炉内钢液受搅拌后混合效果的特征数方程。同时,使用ANSYS CFX软件对原吹气孔及单孔、双孔最佳吹气位置进行数值模拟验证。研究结果表明:钢包吹气位置设在距炉底圆心2/3R处和单孔吹气,钢液混匀时间最短,钢包流场活跃区最大。

关键词: 钢包精炼, 水力模型, 影响因素

Abstract: Based on prototype of steelworks 40t LF, by using the generalized similarity principle, experimental study on the 1:3 water simulation has been carried out. According to Buckingham's π theorem, a characteristic number equation model to describe the effect of mixing molten steel in bottom argon ladle is obtained. Through regression analysis of experimental data, a fitting equation to express mixing effect of stirred liquid in geometric similarity ladle is got. At the same time, the ANSYS CFX software is used to verify the optimal blowing position of the original blowhole and double blowholes. The result of experiment shows that with the argon bubbling at 2/3R distance from the center of bottom and using a single purging plug, the active zone of the ladle is largest and the stirring mixing time is the shortest.

Key words: , Ladle Refining, Water Model, Influencing Factor

欧修龙, 王乐, 王绍明, 王国强. 40t钢包底吹特征的水力学模拟研究[J]. 特殊钢, 2020, 41(5): 14-18.

Ou Xiulong, Wang Le , Wang Shaoming , Wang Guoqiang. Research on Characteristics of 40 t Ladle Bottom Gas Blowing Process by Water Modeling[J]. Special Steel, 2020, 41(5): 14-18.

[1]	王文培, 刘列喜, 李海, 徐雷, 范石伟, 丁理. 高碳绞线钢SWRH82B中心碳偏析控制实践[J]. 特殊钢, 2019, 40(5): 24-27.
[2]	李德军, 许孟春, 李晓伟, 刘祥, 于赋志. 170 ~190tLF精炼过程脱硫影响因素分析[J]. 特殊钢, 2018, 39(5): 32-35.
[3]	傅志强, 姚久红, 朱锦波. 冷轧无取向硅钢片反复弯曲试验的影响因素[J]. 特殊钢, 2008, 29(3): 69-70.
[4]	王广连, 申景霞, 王学利, 孙永喜, 李猛, 翟正龙. 50 t EAF-LF冶炼终点(TPC)和窄成分(NCC)控制技术的应用[J]. 特殊钢, 2007, 28(3): 59-61.
[5]	戴观文 , 梁玫, 武云峰, 刘宪民, 毛天荣, 陈思联, 王新华. 转炉生产热锻非调质钢 F40MnV 的工艺实践[J]. 特殊钢, 2005, 26(3): 57-58.