马氏体钢40Crl0Si2Mo线材表面裂纹原因分析和工艺改进

特殊钢 ›› 2020, Vol. 41 ›› Issue (5): 22-24.

马氏体钢40Crl0Si2Mo线材表面裂纹原因分析和工艺改进

孙增淼，邸永田，姜方，白李国，张荣兴，王刚

邢台钢铁有限责任公司不锈钢公司，邢台054000

收稿日期:2020-04-16 出版日期:2020-10-01 发布日期:2022-05-05
作者简介:孙增4-(1986-)，男，硕士(2015年北京科技大学)，工程师, 2008年北京科技大学(本科)毕业,400系马氏体不锈钢钢种开发。

Analysis on Surface Cracks of Martensitic Steel 40Crl0Si2Mo Wire and Process Improvement

Sun Zengmiao, Di Yongtian, Jiang Fang, Bai Liguo, Zhang Rongxing ， Wang Gang

Xingtai Iron and Steel Co. ,Ltd, Stainless Steel Company, Xingtai 054000

Received:2020-04-16 Published:2020-10-01 Online:2022-05-05

摘要/Abstract

摘要： 40Cr10Si2Mo钢Φ6.5mm线材产品经过调质处理和矫直研磨后,发现磨光棒表面存在表面裂纹。通过进行40Cr10Si2Mo钢淬火回火模拟试验,得出造成40Cr10Si2Mo钢线材表面出现裂纹的原因为线材热轧后冷却时间短,冷却速度快,热轧线材表面存在较大的残余应力,从而形成表面裂纹。通过对40Cr10Si2Mo钢的生产工艺进行了优化改进,包括延长斯太尔摩辊道缓冷时间,终轧温度和吐丝温度由原来的900～950℃和850～900℃均调整为800～850℃,线材轧制后24 h内退火,从而避免了40Cr10Si2Mo钢线材表面裂纹的产生。

关键词: 马氏体气阀钢, 40Crl0Si2Mo, 应力裂纹, 冷却工艺

Abstract: After quenching and tempering, straightening and grinding, the surface cracks are found on the polished rod surface of steel 40Crl0Si2Mo 6. 5 mm wire rod. Through the simulation test of quenching and tempering of steel 40Crl0Si2Mo, it is obtained that the reason for the surface crack of steel 40Crl0Si2Mo wire rod is the short cooling time after hot rolling, the cooling speed is fast, and there is a large residual stress on the surface of the hot rolled wire rod leading to form the surface crack. The production process of steel 40Crl0Si2Mo is optimized and improved, including prolonging Stelmo roller slow cooling time, adjusting the finishing rolling temperature and lay-off temperature from 900 ~ 950 °C and 850 〜900 °C to 800 〜850 °C ,and within 24 hours after rolling to anneal the wire, the surface crack of steel 40Crl0Si2Mo product has been avoided.

Key words: , Martensitic Valve Steel, 40Crl0Si2Mo, Stress Crack, Cooling Process ,

孙增淼, 邸永田, 姜方, 白李国, 张荣兴, 王刚. 马氏体钢40Crl0Si2Mo线材表面裂纹原因分析和工艺改进[J]. 特殊钢, 2020, 41(5): 22-24.

Sun Zengmiao, Di Yongtian, Jiang Fang, Bai Liguo, Zhang Rongxing , Wang Gang. Analysis on Surface Cracks of Martensitic Steel 40Crl0Si2Mo Wire and Process Improvement[J]. Special Steel, 2020, 41(5): 22-24.

[1]	段争涛. 热轧后冷却和平整工艺对700 MPa级Nb-Ti微合金化S600MC高强带钢力学性能的影响[J]. 特殊钢, 2022, 43(5): 92-94.
[2]	马志军. 控轧控冷对38CrMoAl钢盘条硬度的影响和工艺优化[J]. 特殊钢, 2019, 40(3): 35-38.
[3]	彭玉, 任勇, 程晓茹, 范敬国, 沈金龙. 斯太尔摩工艺参数对72A钢盘条氧化铁皮剥离性能的影响[J]. 特殊钢, 2018, 39(3): 20-24.
[4]	杜东福, 赵喜庆, 张建元, 田景林, 贾文军. 提高20CrMnTiH齿轮钢冶金质量的工艺实践[J]. 特殊钢, 2018, 39(2): 34-37.
[5]	余冲, 肖欢. 轧后冷却工艺对模拟CSP含铜Hi-B钢热轧组织和结构的影响[J]. 特殊钢, 2018, 39(2): 56-59.
[6]	徐永, 赵刚, 肖欢, 高建文, 熊韬. 热轧冷却工艺对含铜Hi-B钢抑制剂的影响[J]. 特殊钢, 2016, 37(6): 1-4.
[7]	王伯文, 刘升, 康喜唐, 段政均, 拓雷锋, 李强. 奥氏体不锈钢管热挤压过程挤压针冷却工艺的优化[J]. 特殊钢, 2016, 37(5): 32-35.
[8]	吴乐胜, 方剑, 李明新, 袁泽喜. 定径和冷却工艺参数对40Mn2V钢N80-1套管组织和力学性能的影响[J]. 特殊钢, 2013, 34(6): 45-48.