热处理工艺对硬质合金带锯条背材RM80钢组织和性能的影响

特殊钢 ›› 2018, Vol. 39 ›› Issue (6): 54-57.

热处理工艺对硬质合金带锯条背材RM80钢组织和性能的影响

匡旭光¹, 杨俊²

1湖南泰嘉新材料科技股份有限公司，长沙410200 ；
2中南大学材料科学与工程学院，长沙410083

收稿日期:2018-05-20 出版日期:2018-12-01 发布日期:2022-05-26
作者简介:匡旭光(1987-)，男，硕士(2011年中南大学)，工程师,2008年吉首大学(本科)毕业，硬质合金材料的，热处理、表面处理研究。

Effect of Heat Treatment Process on Microstructure and Properties of Base Steel RM80 for Cemented Carbide Bandsaw Blade

Kuang Xuguang¹ , Yang Jun²

1 Bichamp Cutting Technology Hunan Co. ,Ltd. , Changsha 410200;
2 School of Materials Science and Engineering, Central South University, Changsha 410083

Received:2018-05-20 Published:2018-12-01 Online:2022-05-26

摘要/Abstract

摘要： 以硬质合金带锯条背材RM80为研究对象,采用金相显微镜、扫描电镜(SEM)对金相检测,采用硬度检测仪来检测硬度,通过空转疲劳试验和高速切铜来验证背部的疲劳寿命。结果表明:在高速切削时,硬质合金双金属带锯条背材RM80采用高温短时间淬火最佳,淬火温度范围为1150～1160℃ ,碳化物溶解充分,并且马氏体组织均匀较细;回火最佳温度为640℃左右,组织为回火索氏体。通过高速切削实验,RM80背材的疲劳性能提升约30%。

Abstract: RM80 steel is the research object of this paper, used for the base metal of carbide band saw blade. The metallographic phase was observed by the metallographic microscope and scanning electron microscope were used to observe ; The hardness testing was observed by the hardness tester； Hie flatigue life was verified by the idling fatigue test and high-speed cutting of copper. Hie results show that the quenching at high temperature for shorting time is the best process for RM80 steel during high-speed cutting；the best quenching temperature range is from 1150 ℃ to 1160 ℃, the material with the carbide fully dissolved and even small martensite ；the best tempering temperature is 640 ℃, the metallographic phase of the material is tempering sorbite. Through high-speed cutting experiments, the fatigue performance of the back material of steel RM80 increased by about 30%.

匡旭光, 杨俊. 热处理工艺对硬质合金带锯条背材RM80钢组织和性能的影响[J]. 特殊钢, 2018, 39(6): 54-57.

Kuang Xuguang , Yang Jun. Effect of Heat Treatment Process on Microstructure and Properties of Base Steel RM80 for Cemented Carbide Bandsaw Blade[J]. Special Steel, 2018, 39(6): 54-57.

参考文献

[1]贾寓真，吴懿萍，匡旭光，等.双金属带锯条制造工艺研究进展[J].工具技术.2017,51( 10)： 3-10.
[2]王赛赛，贾非，张兴国，等.双金属带锯条失效原因分析[J].热加工工艺,2014,43(22) ：227-230.
[3]刘年红.中国双金属带锯条行业研究[J].企业技术开发,2010, 29(23):125-127.
[4]陈刚，黄宇，周明哲，等.硬质合金YG8与D6A异种金属CO2激光焊接接头组织和性能的研究[J].湖南大学学报：自然科学版,2017,44 (12) ：34-39.
[5]陈飞雄，强劲熙，贾佐诚.热等静压法制取复合硬质合金轧辊[J].稀有金属材料与工程,1998,27(3)： 177-181.
[6]陈飞雄，李世魁,硬质合金与钢的热等静压扩散连接[J].稀有金属材料与工程,1994,23(4): 46-51.
[7]陈飞雄，强劲熙,贾佐诚.硬质合金与铁基复合材料热等静压扩散连接[J]粉末冶金技术,1995,13 (1)： 8-13.
[8]Lee W B, Kwon B D and Jung S B. Effect of Bonding Time on Joint Properties of Vacuum Brazed WC-Co hard Metal/Carbon Steel using Stacked Cu and Ni alloy as Insert Metal [J]. Materials Science Technology ,2004,20(2) ；1474-1478.
[9]Won Bae Lee, Byoung Dae Kwon and Seung Boo Jung ,et al. Effects of Cr3C2 on the Microstructure and Mechanical Properties of the Brazed Joints Between WC-Co and Carbon Steel [J]. International Journal of Refractory Metals Hard Materials,2006 , 24(3) ：215- 221.
[10]Yi S W and Lee W J. Effects of the Concentration of other Carbides on the Properties of Submicron WC-lOCo Cemented Carbides [J]. Journal of Korean Powder Metallurgy Institute. 1996,22(3) ：86-90.
[11]Zhang J X, Chandel R S and Seow H P. Effects of Chromium on the Interface and Bond Strength of Metal-Ceramic Joints [J]. Materials Chemsislry and Physics,2002,75(6) ：256-259.
[12]Nowacki J and Kawiak M. Defonn ability of WC-Co Sinters andl7-4 PH Steel Brazed Joints [J]. Journal of Materials Processing Technology, 2004, 157(7)： 584-589.
[13]郭喜如，易丹青.粉末高速钢与分齿型硬质合金带锯条锯切钛合金失效模式分析[J].企业技术开发,2015,34(22):25-27.
[14]荀志锋.K24镍基高温合金切削性能试验研究[D].大连:大连理工大学,2003.
[15]付秀丽.高速切削航空铝合金变形理论及加工表面形成特征研[D].济南:山东大学,2007.