热处理对40CrNiMoA钢板焊接接头组织及力学性能的影响

特殊钢 ›› 2022, Vol. 43 ›› Issue (4): 95-99.

热处理对40CrNiMoA钢板焊接接头组织及力学性能的影响

刘艳梅¹，陈静²，王铁钢¹，赵美兰³, 赵夕夕¹，戴慧花¹

1天津职业技术师范大学天津市高速切削与精密加工重点实验室，天津300222；
2中国科学院金属研究所，沈阳110016；
3天津重型装备工程研究有限公司，天津300457

修回日期:2021-12-31 出版日期:2022-08-01 发布日期:2022-08-21
作者简介:刘艳梅(1976-)，女,副教授，硕士(2011年中国科学院金属研究所)，材料分析和变形高温合金工艺研究。
基金资助:
国家自然科学基金(51301181, 51875555)；
天津市科技重大专项(18ZXJMTG00050);
天津市自然科学基金 (19JCYBJC17100 )；
天津市科技特派员项目 (20YDTPJC01460 )；
天津市教委科研计划项目 (2021ZD005)资助

Effect of Heat Treatment on Microstructures and Properties of 40CrNiMoA Steel Plate Welded Joint

LIU Yanmei¹, CHEN Jing², WANG Tiegang¹, ZHAO Meilan³, ZHAO Xixi¹, DAI Huihua¹

1 Tianjin University of Technology and Education, Tianjin Key Laboratory of High Speed Cutting and PrecisionProcessing, Tianjin 300222；
2 Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016；
3 Tianjin Heavy Equipment Engineering Research Co Ltd, Tianjin 300457

Revised:2021-12-31 Published:2022-08-01 Online:2022-08-21

摘要/Abstract

摘要： 本文研究了调质工艺对40CrNiMoA钢板焊接接头显微组织及力学性能的影响。试验结果表明，经 830 - 870 °C +550 - 650 °C 调质处理后,40CrNiMoA钢3 mm板90 A 10 V焊接接头的焊缝区、热影响区、母材区的硬度差异显著减小，形成了回火索氏体组织。调质处理温度越高，焊接接头的焊缝区、热影响区与母材区的组织越均匀,且组织中的碳化物颗粒尺寸增大。40CrNiMoA钢焊接板经850 Y油淬,600 X.回火后，具有较高的强度(905 MPa)和塑性(13. 5% )，综合力学性能最优。

Abstract: Effect of quenching and tempering process on the microstructure and mechanical properties of 40CrNiMoA steel welded joints was studied in this paper. The test results indicated that by quenching + tempering at 830 ~ 870 °C + 550 - 650 °C the 40CrNiMoA steel 3 nun plate at 90A 10V welded joint hardness difference between weld zone, heat affected zone, and base metal zone is reduced significantly, and tempered sorbite structure is formed. The higher quenching and tempering temperature, the more uniform microstructure among the weld zone, heat affected zone and base metal of welded joint, and the cementite particle grew up in structure. The 40CrNiMoA steel welded joint after oil quenching at 850°C and tempering at 600 勾 has higher strength (905 MPa) and plasticity (13. 5% ). In this case, the comprehensive mechanical properties are best.

刘艳梅, 陈静, 王铁钢, 赵美兰, 赵夕夕, 戴慧花. 热处理对40CrNiMoA钢板焊接接头组织及力学性能的影响[J]. 特殊钢, 2022, 43(4): 95-99.

LIU Yanmei, CHEN Jing, WANG Tiegang, ZHAO Meilan, ZHAO Xixi, DAI Huihua. Effect of Heat Treatment on Microstructures and Properties of 40CrNiMoA Steel Plate Welded Joint[J]. Special Steel, 2022, 43(4): 95-99.

参考文献

[1]娄宇航，梁华伟，杜波，等.40CrNiMoA钢与45钢焊接接头组织性能研究[J].焊接技术,2018,47(5) ：26-29 + 8.
[2]王敬忠，李科元,刘阿娇，等-40CrNiMo钢国内外研究现状[J].钢铁,2018,53(5):1-10.
[3]冒健国，张贤，田国祥.40CrNiMoA调质钢MAG焊焊接工艺探讨与应用[J].机械工人,2006,47(9) ：47 + 50.
[4]常川川，李菊,张田仓，等.焊后热处理对高氧TC4/TC17钛合金线性摩擦焊接头组织及性能的影响[J].材料导报,2021,35(10): 10109-10113.
[5]刘艳梅，陈静,赵美兰，等-40CrNiMoA钢同质焊条焊接接头组织和性能研究[JL特殊钢,2020,41(3):5943.
[6]Shen Wei, Qiu Yu and Xu Linzhi, et al. Stress concentration effect of thin plate joints considering welding defects [J]. Ocean Engineering 2019, 184(1)： 273-288.
[7]周杰.热处理工艺对爆炸焊接C276/Q345R金属复合板性能的影响[J].金属世界,2021 (3)：18-2L
[8]Zhang Min, Zhang Tao and Cai Junqing, et al. Effect of Heat Treatment on Microstucture and Properties of Explosive Welding Clad Plate of TA1/Q345 [J]. China Welding, 2018 , 27(1)：26-31.
[9]白凤臣，马文姝,于彦东，等.热处理对TP3O4H/R1O2异种钢焊接接头组织和性能的影响[J].焊接,2020(7) ：55-60 +63-64.
[10]孙兴德.40CrNiMo钢退火热处理工艺与性能的研究[J].金属制品,2014,40(3):19-22.
[11]刘乐-40CrNiMo钢棍轴的热处理工艺[J].金属热处理,2013, 38(10):84-55. [12]方洪渊.焊接结构学[M].北京:机械工业出版社(第二版)， 2008:62-68,72-130.
[13]刘旭辉，张波，肖爱达，等.工程机械用960QT钢焊接粗晶区组织及性能研究[J].特殊钢，2019,40(1):63-67.
[14]Tang Wenshen, Yang Xinqi and Li Shengli, et al. Microstructure and Properties of CLAM/316L Steel Friction Stir Welded Joints [J]. Journal of Materials Processing Technology, 2019 , 271: 189201.
[15]刘畅,邓彩艳，王胜,等.EH36钢埋弧焊焊缝金属组织临界断裂韧性[J].焊接学报,2019,40(3):107-110 +165-166.
[17]梅珍，蒋波,董正强，等.热处理参数对40CrNiMo钢硬度和韧性的影响[A].中国金属学会、宝钢集团有限公司.“第十届中国钢铁年会“暨”第六届宝钢学术年会”论文集[C].中国金属学会、宝钢集团有限公司：中国金属学会,2015 ：5.