深冲用超低碳冷轧带钢铁素体区热轧的现场试验

特殊钢 ›› 2009, Vol. 30 ›› Issue (3): 30-33.

深冲用超低碳冷轧带钢铁素体区热轧的现场试验

肖鸿飞¹, 李壮², 吴迪³, 王昭东³

1沈阳大学理工学院，沈阳110044；
2沈阳航空工业学院材料科学与工程学院，沈阳110034；
3东北大学轧制技术及连轧自动化国家重点实验室，沈阳H0004

收稿日期:2008-11-20 出版日期:2009-06-01 发布日期:2022-11-24
作者简介:肖鸿飞(1961-),女，教授，硕士生导师,1983年辽宁大学毕业，理论物理、力学与应用研究。李壮(1964-),男，博士后,副教授,1986年吉林工业大学毕业,钢铁材料组织和性能研究。
基金资助:
国家自然科学基金资助项目(50104004)

Pilot Production of Hot Rolling in Ferrite Region for Cold Rolled Extra-low Carbon Steel Strip for Deep Drawing

Xiao Hongfei¹, Li Zhuang², Wu Di³ , Wang Zhaodong³#br#

1 College of Science, Shenyang University, Sheyang 110044 ；
2 School of Materials Science & Engineering, Shenyang Institute of Aeronautical Engineering, Shenyang 110034；
3 Stat Key Lab of Rolling and Automation, Northeastern University, Shenyang 110004)

Received:2008-11-20 Published:2009-06-01 Online:2022-11-24

摘要/Abstract

摘要： 研究和对比了经1 880 mm热轧机组在奥氏体区(945～848℃)和铁素体区(803～755℃)热精轧,卷取温度700℃以及73%压下率冷轧的3.0 mm超低碳带钢(%:0.008C、0.029Als、0.000 8B、0.001 4N)退火后的组织和性能。结果表明,与奥氏体区轧制比较,热轧采用铁素体区轧制的710℃退火后冷轧带钢具有较高的伸长率、塑性应变比(r值)和应变硬化指数(n),因而具有较好的深冲性能。

关键词: 超低碳冷轧带钢, 铁素体区轧制, 深冲性能

Abstract: Structure and properties of 3. 0 inm extra-low carbon steel strip ( % : 0. 008C, 0. 029Als, 0. 000 8 B, 0. 001 4N) hot finish-rolled by 1 880 mm hot rolling mill train in austenite region (945 ~ 848 °C ) and in ferrite region (803 - 755 °C ) , coiled at 700 °C , then cold rolled with 73% reduction and annealed have been studied and compared. Results showed that as compared with austenite region rolling, with ferrite region rolling the cold rolled steel strip annealed at 710 °C had higher elongation, plastic Strain ratio (r) and strain-hardening exponent (n) , therefore it had better deep drawability.

Key words: Cold Rolled Extra-low Carbon Steel Strip, Rolled in Ferrite Region, Deep Drawability

肖鸿飞, 李壮, 吴迪, 王昭东. 深冲用超低碳冷轧带钢铁素体区热轧的现场试验[J]. 特殊钢, 2009, 30(3): 30-33.

Xiao Hongfei , Li Zhuang, Wu Di, Wang Zhaodong. Pilot Production of Hot Rolling in Ferrite Region for Cold Rolled Extra-low Carbon Steel Strip for Deep Drawing[J]. Special Steel, 2009, 30(3): 30-33.