26CrMo4V钢高抗挤套管内折叠的分析和改进工艺措施

特殊钢 ›› 2008, Vol. 29 ›› Issue (6): 31-33.

26CrMo4V钢高抗挤套管内折叠的分析和改进工艺措施

孙开明^1,2，李士琦¹，张传友²，郁健¹

1北京科技大学冶金与生态工程学院，北京100083;
2天津钢管集团股份有限公司技术中心，天津300301

收稿日期:2008-05-21 出版日期:2008-12-01 发布日期:2022-12-07
作者简介:孙开明(1959-),男，总工程师，教授级高级工程师，1982年北京科技大学毕业，钢铁冶金和无缝钢管制造。
基金资助:
国家863课题资助项目(2007AA03Z509)

An Analysis on Inner Overlap of High Anti-Collapse Strength Seamless Casing Tube of Steel 26CrMo4V and Improved Technology Measure

Sun Kaiming^1,2,Li Shiqi¹,Zhang Chuanyou²，Yu jian¹

1 School of Metallurgical and Ecological Engineering,University of Science and Technology,Beijing 100083;
2 Technology Center,Tianjin Pipe(Group)Corp Ltd,Tianjin 300301

Received:2008-05-21 Published:2008-12-01 Online:2022-12-07

摘要/Abstract

摘要： 26CrMo4V钢(%:0.26C、0.95Cr、0.16Mo、0.07V)Φ245 mm×12 mm套管内壁凸包折叠的分析表明,该缺陷有沿套管内壁同侧随机分布的规律性,凸包内存在Si、Mn、Fe复合氧化层。认为在穿孔时,连铸坯中的偏心缩孔内壁形成的稳定氧化层阻止缩孔内壁界面的"焊合",在剪切-拉伸应变的作用下,形成内折叠缺陷。通过低过热度、弱二冷和控制拉坯速度等工艺措施,使内折报废率从15.43%降至5.95%。

关键词: 26CrMo4V钢, 套管, 内折叠 , 连铸工艺

Abstract: It was indicated by analysis on bulge-like inner overlap of Φ245 mm×12 mm casing tube of steel 26CrMo4V(0.26C,0.95Cr,0. 16Mo,0.07V)that the defects distributed random at the same side of inner wall and there was Si-Mn-Fe compound oxide layer in overlap.It was considered that the bonding of eccentric shrinkage cavity in cast bloom was prevented in piercing by the stable oxide layer which formed at inner wall of eccentric shrinkage cavity,and the inner overlap defects formed at action of combined shear and tensile strains during piercing.With the technology measures such as lower overheating of liquid steel,weak secondary water cooling and controlling casting speed,the reject ratio of tube with inner overlap decreased to 5.95% from original 15.43%.

Key words: Steel 26CrMo4V,Casing Tube,Inner Overlap,Concasting Technology

孙开明, 李士琦, 张传友, 郁健 . 26CrMo4V钢高抗挤套管内折叠的分析和改进工艺措施[J]. 特殊钢, 2008, 29(6): 31-33.

Sun Kaiming, Li Shiqi, Zhang Chuanyou, Yu jian. An Analysis on Inner Overlap of High Anti-Collapse Strength Seamless Casing Tube of Steel 26CrMo4V and Improved Technology Measure[J]. Special Steel, 2008, 29(6): 31-33.

[1]	吴亮亮, 吴永超, 周家祥, 张旭. 高强度热采套管TP110H的350 ℃高温力学性能研究[J]. 特殊钢, 2023, 44(4): 125-128.
[2]	宋景凌, 周旋, 李恒华. 石油套管用37Mn5钢全流程洁净度分析及工艺改进[J]. 特殊钢, 2023, 44(4): 58-64.
[3]	张新文, 朱康宁, 孟祥岩, 轩康乐. H13钢Φ130 ~ 150 mm热轧材探伤不合格原因分析及改进措施[J]. 特殊钢, 2022, 43(5): 55-58.
[4]	胡楚江, 邓叙燕, 潘恩宝, 程凯. 非调质钢N80 Φ139.7 mm×9.17 mm石油套管的研制[J]. 特殊钢, 2020, 41(4): 19-21.
[5]	唐科, 王秀敏, 彭俊, 杨煌光, 张银桥. 稠油热采井用110SH-1钢级热釆套管的开发[J]. 特殊钢, 2020, 41(4): 43-47.
[6]	程凯, 冯莹, 邓叙燕, 刘珂, 李英真 . L80-1级高抗挤毁石油套管用钢29MnCr6的开发[J]. 特殊钢, 2019, 40(2): 31-34.
[7]	方剑, 黄彦, 唐应波. 热处理对Φ245 mmx l2 mm V150高抗挤毁套管用钢27CrMnMoV组织和性能的影响[J]. 特殊钢, 2018, 39(3): 54-58.
[8]	邢娜, 黄宝, 何立波, 赵婷婷. 酸性环境用油气专用无缝钢管的研发现状[J]. 特殊钢, 2016, 37(3): 20-24.
[9]	吕国成, 包丽明, 朱金禄, 尚冰. Nb-Ti微合金化含铬J55石油套管用钢的生产实践[J]. 特殊钢, 2015, 36(4): 28-30.
[10]	朱新华, 朱立光, 孙向东, 孟娜. 石油套管用钢37Mn5 Φ210 mm连铸圆坯凝固过程的数学模拟和工艺优化[J]. 特殊钢, 2014, 35(6): 5-8.
[11]	方忠强, 孙彦辉, 汪成义, 蔡开科. 120 t BOF-LF-RH-CC流程冶炼石油套管钢时TiN的析出和控制[J]. 特殊钢, 2014, 35(5): 30-33.
[12]	王旭东, 尹少华, 孔令伟, 姚曼, 张晓兵, 陆洪周, 王雄, 倪涛. 碳含量及连铸工艺参数对宽厚板坯结晶器热流的影响[J]. 特殊钢, 2014, 35(4): 36-40.
[13]	吴乐胜, 方剑, 李明新, 袁泽喜. 定径和冷却工艺参数对40Mn2V钢N80-1套管组织和力学性能的影响[J]. 特殊钢, 2013, 34(6): 45-48.
[14]	张玉海, 王永然. 石油套管钢Φ150～Φ200mm连铸圆坯的质量控制[J]. 特殊钢, 2013, 34(3): 42-44.
[15]	王韬, 陈伟庆, 王宏斌, 王建忠, 张志强. 连铸参数和末端电磁搅拌对82B钢小方坯中心碳偏析的影响[J]. 特殊钢, 2013, 34(1): 49-51.