RH-PTB真空精炼装置内粉剂混合特性的水模型研究

特殊钢 ›› 2005, Vol. 26 ›› Issue (5): 16-18.

RH-PTB真空精炼装置内粉剂混合特性的水模型研究

杜成武, 朱苗勇, 潘时松, 郑淑国

东北大学材料与冶金学院，沈阳 110004

收稿日期:2005-04-11 出版日期:2005-10-01 发布日期:2023-03-30
作者简介:杜成武(1966-)，男，博士研究生，副教授。从事钢铁冶金的教学与科研工作。
基金资助:
国家技术创新资助项目(01BK-098-02-01)
辽宁省教育厅高校科学研究资助项目(2004D271)

A Study of Water Model on Mixing Characteristics of Powder Injected through Top Lance in RH-PTB Vacuum Refining Unit

Du Chengwu , Zhu Miaoyong , Pan Shisong , Zheng Shuguo

School of Materials and Metallurgy,Northeastern University,Shenyang 110004

Received:2005-04-11 Published:2005-10-01 Online:2023-03-30

摘要/Abstract

摘要： 根据相似理论,用1∶9水模型钢包(直径0.43m,水面高度0.45m)模拟RH-PTB真空精炼水冷顶枪喷粉技术,研究顶枪气量、上升管提升气量、顶枪枪位高度对粉剂混均时间的影响。结果表明,随顶枪气量增加,粉剂在液体中均混时间增加,并具有最大值;随提升气量增加,均混时间迅速减少,但当提升气量≥15L/min时,均混时间不再继续减少;顶枪枪位对均混时间有一定影响,实际操作中,应根据具体情况,调整顶枪枪位,以减少粉剂均混时间。

关键词: RH-PTB真空精炼, 粉剂, 均混时间

Abstract: Based on theory of similarity,the powder injected through top lance in RH-PTB vacuum refining has been simulated using 1:9 water model ladle(diameter-0.43 m,height to water surface-0.45 m)to study the effect of top lance gas flow rate,lifting gas flow rate of up-leg and height of top lance on injecting powder mixing time in liquid. The results showed that with top lance gas flow rate increasing,the injecting powder mixing time in liquid increased and had maximum value; with lifting gas flow rate of up-leg increasing,the mixing time quickly decreased and as lifting gas flow rate was ≥15 L/min,the mixing time was no longer decreasing; the effect of height of top lance on mixing time was definite,therefore in operation,according to specific circumstances to adjust height of top lance decreasing powder mixing time.

Key words: RH-PTB Vacuum Refining, Powder, Mixing Time

杜成武, 朱苗勇, 潘时松, 郑淑国. RH-PTB真空精炼装置内粉剂混合特性的水模型研究[J]. 特殊钢, 2005, 26(5): 16-18.

Du Chengwu , Zhu Miaoyong , Pan Shisong , Zheng Shuguo. A Study of Water Model on Mixing Characteristics of Powder Injected through Top Lance in RH-PTB Vacuum Refining Unit[J]. Special Steel, 2005, 26(5): 16-18.

参考文献

[1] 冈田泰和，家田幸治，真屋敬一，等.RH 粉体上.吹精炼法)开发.铁上钢，1994,80(1):9
[2] Krwabara T,Umezawa K,Mori K,et al. Investigation of Decarburization Behavior in RH-Reactor and Its Operation Improvement.Transactions ISIJ,1988,28(4):305
[3] 朱苗勇，沙骏，黄宗泽.RH 真空精炼装置内钢液流动行为的数值模拟.金属学报，2000,36(11):1175
[4] Sehadri V.Cold Model Studies of RH Degassing Process. Transaction ISIJ,1986,26(2):133
[5] 郁能文，魏季和，樊养颐，等.RH 精炼过程中钢液流动特性的水模型.东北大学学报，1998,19(S1):118
[6] Kato Y,Nakato H,Fujii T,et al.Fuid Flow in Ladle and Its Effect on Decarburization Rate in RH Degasser.ISIJ International,1993,33(10):1088
[7] 金永刚，许海虹，朱苗勇.RH 真空脱气动力学过程的物理模拟研究.炼钢，2000,16(5):39
[8] 金水刚，许海虹，朱苗勇.RH-KTB 精炼中钢液溶氧过程动力学的水模拟研究.钢铁研究学报，2001,13(3):1
[9] 朱苗勇，黄宗泽.RH 真空脱碳精炼过程的模拟研究.金属学报，2001,37(1):91
[10] Chosh D N and Lange K W.Bahaviour of Jets df Argon-bome Particles Irjected Into Lixquids.Ironmaking and Steelmaking,1983,9(3): 136
[11] Varadarajan Shshadri,Carlos Antonio Da Silva, ltavahn Alves Da Silva,et al. A Kinetic Model Applied to the Molten Pig Iron Desulfurization by Injection of Limed-based Powders.ISIJ International,1997,37(1):21
[12] Satish C.Koria and Rajiv Duta.Study of the Effect of Some Process Parareters on Powder Injection Refining by a Mathenatical Model. Scandinavian Journal of Metallurgy,2000,29:259
[13] Van Poucke N,Peeters L, Haers(Sidmar)F.Improvement of Dephosphorization and Decarburization by Injection of Metallurgical Powders in the RH.La Revue de Meallurgie-CIT,2000,4:527
[14] Irons C.A.Role of Mixing in Powder Injection Desulphurisation Processes.Ironmaking and Steelmaking,1989,16(1):28