GCr15轴承钢棒材连轧过程的二维和三维模拟

廖舒纶; 张立文; 岳重祥; 高惠菊; 郭书奇

您当前的位置：

首页 >

文章列表页 >

GCr15轴承钢棒材连轧过程的二维和三维模拟

试验研究 | 更新时间：2026-01-21

- GCr15轴承钢棒材连轧过程的二维和三维模拟
- Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15
- 特殊钢 2007年28卷第5期页码：31-33
- 作者机构：
  
  1. 大连理工大学材料科学与工程学院,大连,116023
  2. 东北特钢集团棒线材连轧厂,大连,116031
- 作者简介：
  
  [ "廖舒纶(1980-)，男，博士研究生，从事棒线材轧制过程的数值模拟和工艺优化。" ]
- 基金信息：
- DOI：
  中图分类号：
- 收稿：2007-04-18，
  
  网络首发：2023-02-13，
  
  纸质出版：2007-02-13
- 稿件说明：
移动端阅览
廖舒纶, 张立文, 岳重祥, 等. GCr15轴承钢棒材连轧过程的二维和三维模拟[J]. 特殊钢, 2007,28(5):31-33.

廖舒纶, 张立文, 岳重祥, et al. Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15[J]. Special Steel, 2007, 28(5): 31-33.
廖舒纶, 张立文, 岳重祥, 等. GCr15轴承钢棒材连轧过程的二维和三维模拟[J]. 特殊钢, 2007,28(5):31-33. DOI：

廖舒纶, 张立文, 岳重祥, et al. Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15[J]. Special Steel, 2007, 28(5): 31-33. DOI：

摘要

借助商业有限元软件MSC.Marc建立了GCr15轴承钢150 mm×150 mm坯至φ32 mm棒材的12道次连轧过程的二维和三维模型

并对比了二维和三维模型对轧制过程轧件截面形状、温度的模拟结果。结果表明

与三维模型相比

二维模型模拟得到的轧件截面宽展偏大

但计算效率较高

得出的温度曲线接近三维模型的模拟结果;给定工艺参数的三维模拟较二维模拟准确;模型模拟得到的出口轧制速度和温度与实测值吻合。

Abstract

The two- and three-dimensional models of 12 pass continuous rolling process for 150 mm × 150 mm billet to φ32 mm rod have been established by commercial finite element software MSC .Marc

and the simulation results of cross section shape

temperature of rolling stock during rolling process by two- and three-dimensional models were compared. Results showed that as compared with that calculated by three dimensional model

the width spread of cross section calculated by two-dimensional model is larger but by which the computational efficiency is high and the temperature curves were close to that calculated by three dimensional model; the three dimensional simulation on given process parameter was more accurate than two dimensional simulation; the simulated value of exit rolling speed and temperature obtained by simulation agreed with experimental value.

关键词

Keywords

references

浏览量

下载量

CSCD

CNKI被引量

文章被引用时，请邮件提醒。

提交

工具集

关联资源

轧制变形对U75V重轨钢珠光体片层间距的影响

N80级非调质油井管用钢36-40Mn2V连轧和定径工艺对组织和性能的影响