200 mm x200 mm连铸坯连轧Φ100 mm 42CrMo钢三维有限元模拟

魏军; 洪慧平; 赵爱民; 康永林

您当前的位置：

首页 >

文章列表页 >

200 mm x200 mm连铸坯连轧Φ100 mm 42CrMo钢三维有限元模拟

试验研究 | 更新时间：2026-01-21

- 200 mm x200 mm连铸坯连轧Φ100 mm 42CrMo钢三维有限元模拟
- 3-Demensional Finite Element Simulation on Continuous Rolling Φ100 mm Steel 42CrMo by 200 mm x200 mm Cast Bloom
- 特殊钢 2010年31卷第1期页码：1-3
- 作者机构：
  
  1. 北京科技大学材料科学与工程学院,北京,100083
  2. 承德建龙特殊钢有限公司,承德,067201
- 作者简介：
  
  [ "魏军（ 1969-）,男，博士后，特种钢质量研究。" ]
- 基金信息：
- DOI：
  中图分类号：
- 收稿：2009-07-09，
  
  网络首发：2022-10-24，
  
  纸质出版：2010-10-24
- 稿件说明：
移动端阅览
魏军, 洪慧平, 赵爱民, 等. 200 mm x200 mm连铸坯连轧Φ100 mm 42CrMo钢三维有限元模拟[J]. 特殊钢, 2010,31(1):1-3.

魏军, 洪慧平, 赵爱民, et al. 3-Demensional Finite Element Simulation on Continuous Rolling Φ100 mm Steel 42CrMo by 200 mm x200 mm Cast Bloom[J]. Special Steel, 2010, 31(1): 1-3.
魏军, 洪慧平, 赵爱民, 等. 200 mm x200 mm连铸坯连轧Φ100 mm 42CrMo钢三维有限元模拟[J]. 特殊钢, 2010,31(1):1-3. DOI：

魏军, 洪慧平, 赵爱民, et al. 3-Demensional Finite Element Simulation on Continuous Rolling Φ100 mm Steel 42CrMo by 200 mm x200 mm Cast Bloom[J]. Special Steel, 2010, 31(1): 1-3. DOI：

摘要

采用MSC.Marc有限元模拟软件

针对200 mm×200 mm连铸方坯连轧Φ100 mm 42CrMo圆钢工艺过程进行三维热力耦合模拟仿真。因圆角在孔型中塑性应变较大且变形由表及里逐渐深入

因此对断面采用网格偏差划分方法以细分表层及圆角区域单元。根据连轧过程应力场、应变场和温度分布及轧制力和轧制力矩变化特点

得出合金钢轧制时圆角易出现裂纹的重要原因是该区域总等效塑性应变、等效应力和温降较大。机架间及轧后断面尺寸实测值与模拟值相符合。

Abstract

3-demensional thermodynamic coupling simulation for continuous rolling process of Φ100 mm round steel 42CrMo by 200 mm x 200 mm cast bloom has been carried out by using MSC. Marc finite element simulation software. As the plastic stain at round comer of stock in pass is larger and the deformation is gradually from surface to inner

the method of grid deviation division for cross section is adopted to fine the element of surface and round comer area. Based on the characteristics of stress field

strain field and temperature distribution as well as change of rolling force and torque during continuous rolling process

it is obtained that during alloy steel rolling

the larger total equivalent strain

equivalent stress and temperature drop are key reason of occurred crack at round comer of stock. The simulated values of cross section size of stock between stands and after rolling correspond to the measured values.

关键词

Keywords

references

浏览量

下载量

CSCD

CNKI被引量

文章被引用时，请邮件提醒。

提交

工具集

关联资源

GCrl5轴承钢棒材连轧过程的有限元模拟

高碳钢连铸坯加热脱碳的有限元模拟

控轧控冷和冷床保温工艺对42CrMo钢φ50 mm轧材力学性能的影响

Q235/304碳钢-不锈钢复合板界面结合的有限元模拟

平三角孔型轧制钛合金棒材温度场的有限元模拟