150t 顶底复吹转炉-150 t钢包炉生产60Si2Mn(A) 弹簧钢的 工艺和质量

特殊钢 ›› 2006, Vol. 27 ›› Issue (4): 39-41.

150t 顶底复吹转炉-150 t钢包炉生产60Si2Mn(A) 弹簧钢的工艺和质量

梁福斌, 刘新生

河北理工大学冶金与能源学院，唐山063009

收稿日期:2006-02-24 出版日期:2006-08-01 发布日期:2023-03-17
作者简介:梁福斌(1950-),男，教授，1976年河北矿冶学院毕业，炼钢新技术开发和应用。

Process and Quality of Spring Steel 60Si2Mn(A)Produced by an 150 t Top and Bottom Combined Converter -150 t Ladle Furnace

Liang Fubin, Liu Xinsheng

School of Metallurgy and Energy Resource,Hebei Palytechnic University,Tangshan 063009

Received:2006-02-24 Published:2006-08-01 Online:2023-03-17

摘要/Abstract

摘要： 采用150 t顶底复吹转炉-150 t LF精炼(加铝1．2 kg／t、钡合金1．0 kg／t、Ar气搅拌、喂SiCa线)-165 mm×165 mm方坯连铸机生产60Si2Mn(A)弹簧钢。LF末期钢中氧含量为(15～25)×10^-6,残余铝含量0．020％-0．030％。铸坯的低倍组织、二次枝晶间距和电解夹杂物分析结果表明,铸坯的组织致密;钢中大部分夹杂物为尺寸≤20μm的颗粒状SiO₂、球形(Mn,Fe)O·SiO₂和MnS,说明钡合金的使用,有利于降低钢中氧含量和改变夹杂物的形态。

关键词: 顶底复吹转炉, 60Si2Mn(A)弹簧钢, LF精炼, , Ba合金, 夹杂物

Abstract: The spring steel 60Si2Mn(A)was produced by an 150 top and bottom combined converter - 150 t ladle furnace(adding Al 1.2kg/t, Ba alloy 1.0 kg/t, Ar stiring, feeding SiCa wire)- 165 mmx165 mm billet concaster.The oxygen content in steel at end phase of ladle furnace was (15~25)×10^-6 and residual aluminium was 0.020%～0.030%.The results of analysis on macrostructure of billet, distance between secondary crystal branches and electrolytic analysis of inclusion showed that the most of inclusion in steel were SiO₂ particle,spherical (Mn,Fe)O · SiO₂ and MnS with size ≤20 pm. It proves that added barium alloy is available decreasing oxygen content in steel and modifying morphology of inclusion.

梁福斌, 刘新生. 150t 顶底复吹转炉-150 t钢包炉生产60Si2Mn(A) 弹簧钢的工艺和质量[J]. 特殊钢, 2006, 27(4): 39-41.

Liang Fubin , Liu Xinsheng. Process and Quality of Spring Steel 60Si2Mn(A)Produced by an 150 t Top and Bottom Combined Converter -150 t Ladle Furnace[J]. Special Steel, 2006, 27(4): 39-41.