超低氧钢20CrMoH和60Si2MnA中TiN夹杂的控制

特殊钢 ›› 2008, Vol. 29 ›› Issue (2): 44-46.

超低氧钢20CrMoH和60Si2MnA中TiN夹杂的控制

李海波¹王郢²王新华² 王万军¹张玮²

1北京科技大学冶金与生态工程学院，北京W0083； 2首钢技术研究院，北京100041

出版日期:2008-04-01 发布日期:2023-01-20
作者简介:李海波(1975-)，男,博士生,2008年北京科技大学毕业，纯净钢冶炼和钢中非金属夹杂的研究。

Control of TiN Inclusion in Ultra-low Oxygen#br# Steel 20CrMoH and 60Si2MnA#br#

Li Hiabo1, Wang Ying¹, Wang Xinhua¹, Wang Wanjun¹ and Zhang Wei²

1 School of Metallurgical and Ecological Engineering, University of Science and Technology, Beijing 100083 ；
2 Shougang Research Institute of Technology, Beijing 100041

Published:2008-04-01 Online:2023-01-20

摘要/Abstract

摘要： 研究了超低氧(10 x 10^-6)钢20CrMoH和60Si2MnA转炉终点[C]和LF渣(TiO₂)对转炉终点[Ti[和 LF精炼过程A[Ti]的影响，以及[S]、[ N]对TiN生成的影响。结果表明,试验钢TiN夹杂有两类：(1)单独TiN； (2)CaS为核心的复合TiN。20CrMoH钢中TiN夹杂较少,60Si2MnA钢中TiN占夹杂总量的50% ~60%。随铸坯中S含量的增加,TiN夹杂含量增加；当[Ti]为(69~80) x10^-6,[N]、[S]分别从(60~74) x 10^-6和⑶~ 35) x 10"降至(27 ~35) x10^-6和(14~20) x 10^-6时,TiN 个数从 4.4 ~ 6.1 个/cm²降低到 0.4 ~ 1.1 个/cm²；当[S]w 0. 002%，钢中无CaS-TiN复合夹杂析出。

关键词: 超低氧 , 20CrMoH钢 , 60Si2MnA钢 , TiN , 工艺控制

Abstract: The effect of converter end [ C ] and (TiO₂) in LF slag on converter end [Ti] and A [Ti] during LF refining process, as well as the effect of [ S] and [ N] on formation of TiN in ultra-low oxygen ([ 0 ] 10 x 10^-6) steel 20CrMoH and steel 60Si2MnA have been studied. Results showed that there were two kinds of TiN inclusion: (1) individual TiN and (2) compound TiN with core of CaS； TiN was minor in inclusions in steel 20CrMoH, but TiN accounted fbr 50% - 60% of total inclusions in steel 60Si2MnA； with increasing S content in cast billet the TiN content increased；as [Ti] was (69 -80) x 10^-6, [N] and [S] respectively decreased from (60 〜74) x 10^-6 and (30 ~35) x 10^-6 to (27 - 35) x 10^-6 and (14 -20) x 10^-6, the TiN number decreased from 4.4 -6.1 per cm² to 0.4 - 1, 1 per cm² ； and as [S] W0. 002% , there was no CaS-TiN compound inclusion precipitated in steel.

Key words: Ultra-low Oxygen, Steel 20CrMoH, Steel 60Si2MnA, TiN, Process Control

李海波王郢王新华王万军张玮 . 超低氧钢20CrMoH和60Si2MnA中TiN夹杂的控制[J]. 特殊钢, 2008, 29(2): 44-46.

Li Hiabo, Wang Ying, Wang Xinhua, Wang Wanjun and Zhang Wei. Control of TiN Inclusion in Ultra-low Oxygen#br# Steel 20CrMoH and 60Si2MnA#br#[J]. Special Steel, 2008, 29(2): 44-46.

[1]	赵满堂, 陈永峰, 陶群南, 林作津, 史杨. 低合金高强度30CrMnTi盘条钢的开发实践[J]. 特殊钢, 2021, 42(1): 29-31.
[2]	李永超, 李瑞, 李家杨, 韩广杰. 汽车发动机气门挺柱用16MnCr5冷镦钢盘条的研发与生产[J]. 特殊钢, 2020, 41(6): 24-27.
[3]	姜颖, 徐华, 黄微涛, 向浪涛, . 压力容器用钢板ASTM A 387M Gr. 11 CL2的生产实践[J]. 特殊钢, 2020, 41(4): 40-42.
[4]	马志军, 王鲁义, 方元杰. 60Si2MnA弹簧钢盘条脱碳层控制工艺的优化[J]. 特殊钢, 2016, 37(4): 26-28.
[5]	李永超, 陈继林, 郭明仪, . 高强度螺栓用QB30冷镦钢盘条的研发与生产[J]. 特殊钢, 2016, 37(4): 33-36.
[6]	苏瑞先. 连铸夹渣类缺陷的成因分析和控制措施[J]. 特殊钢, 2011, 32(1): 27-29.
[7]	魏军, 洪慧平, 廖向军, 王孟, 李春雨, 康永林. 37Mn5钢管外折叠成因分析和工艺控制[J]. 特殊钢, 2010, 31(1): 30-32.
[8]	陈永, 杨素波, 朱苗勇. 高压气瓶钢34Mn2V 200 mm×200 mm轧坯角部拉裂缺陷的控制工艺[J]. 特殊钢, 2008, 29(6): 28-30.
[9]	李冬生 , 徐冠宇. EAF-LF-CC工艺冶炼的结构钢低倍夹杂物的分析和控制[J]. 特殊钢, 2007, 28(1): 59-60.