00Cr25Ni7Mo4N超级双相不锈钢热加工性能的研究

特殊钢 ›› 2008, Vol. 29 ›› Issue (5): 29-31.

00Cr25Ni7Mo4N超级双相不锈钢热加工性能的研究

王晓峰¹，陈伟庆¹，宋红梅²

1. 北京科技大学冶金与生态工程学院，北京 100083;
2. 宝钢研究院不锈钢技术中心，上海 201900;

收稿日期:2008-04-03 出版日期:2008-10-01 发布日期:2023-01-04
作者简介:王晓峰(1979-)，男，博士研究生，从事不锈钢研究。

A Study on Hot Workability of Super Duplex Stainless Steel 00Cr25Ni7Mo4N

Wang Xiaofeng¹ , Chen Weiqing¹ , Song Hongmei²

1. School of Metallurgical and Ecological Engineering,University of Science and Technology,Beijing 100083;
2. Technology Center of Stainless Steel,Baosteel Institute,Shanghai 201900;

Received:2008-04-03 Published:2008-10-01 Online:2023-01-04

摘要/Abstract

摘要： 通过Gleeble热模拟机对真空感应炉熔炼的00Cr25Ni7Mo4N锻材进行高温拉伸和单道次及连续4道次压缩试验。结果表明,在900～1 250℃的范围内随温度提高和在950～1 100℃时随道次递增,00Cr25Ni7Mo4N钢的最大变形抗力逐渐下降;在1 050～1 250℃时,00Cr25Ni7Mo4N钢的变形抗力较低,断面收缩率高于60%,具有较好的热塑性;当应变速率为10/s且温度高于1 000℃,及应变速率为50/s且温度高于1 100℃时,钢的热加工性较好。

关键词: 双相不锈00Cr25Ni7Mo4N, 应力-应变, 热加工性

Abstract: Test of tensile properties and compression with single pass and continuous 4 pass at elevated temperature for forged bar of steel 00Cr25Ni7Mo4N melted by vacuum induction funace has been carried out by Gleeble thermal simulator. Results showed that at 900～1250 ℃,with increasing temperature and at 950～1100 ℃ with progresive increasing pass,the maximum deformation resistance of steel 00Cr25Ni7Mo4N gradually decreased; at 1050~1250 ℃ the deformation resistance of steel 00Cr25Ni7Mo4N was lower and the reduction of area was more than 60% with better hot plasticity; the steel had better hot workability as strain rate 10/s at≥1000℃ and as strain rate 50/s at ≥1100 ℃.

Key words: Duplex Stainless Steel 00Cr25Ni7Mo4N, Stress-Strain, Hot Workability

王晓峰, 陈伟庆, 宋红梅. 00Cr25Ni7Mo4N超级双相不锈钢热加工性能的研究[J]. 特殊钢, 2008, 29(5): 29-31.

Wang Xiaofeng , Chen Weiqing , Song Hongmei. A Study on Hot Workability of Super Duplex Stainless Steel 00Cr25Ni7Mo4N[J]. Special Steel, 2008, 29(5): 29-31.

[1]	帅勇, 孙乐飞, 陈英俊. 690 MPa高强度海洋工程用钢1 000 ~ 1100 ℃热变形行为[J]. 特殊钢, 2015, 36(4): 66-69.
[2]	俞飞 , 宋志刚, 郑文杰 , 郭忠诚, 季祥民 , 丰涵. 铈对超级双相不锈钢00Cr25Ni7Mo4N热加工性能的影响[J]. 特殊钢, 2010, 31(4): 58-60.
[3]	包耀宗, 董瀚, 苏杰, 雍岐龙, 王黎辉, 李明志. 耐蚀合金G3、G3-Z和825热加工性的研究[J]. 特殊钢, 2009, 30(5): 1-3.
[4]	刘平, 李峰, 陈爱梅, 史凤武. Nb-和V-微合金化对高碳钢热加工性的影响[J]. 特殊钢, 2008, 29(6): 13-14.
[5]	关云, 李平和, 陈庆丰, 刘继雄. 变形量及碳含量对超低碳贝氏体钢动态再结晶的影响[J]. 特殊钢, 2007, 28(6): 24-26.
[6]	王生朝, 张永青. 含Nb微合金钢Q345E热变形行为研究[J]. 特殊钢, 2005, 26(6): 35-37.
[7]	魏立群. B30MnSi钢的动态再结晶行为[J]. 特殊钢, 2005, 26(4): 13-15.
[8]	何建中, 刘雅政, 史秉华, 刘清友, 王雪莲, 李德刚. Q345含Nb低碳钢CSP轧制时动态再结晶的研究[J]. 特殊钢, 2005, 26(3): 9-11.