提高亚包晶钢板坯拉速对结晶器传热的影响

特殊钢 ›› 2009, Vol. 30 ›› Issue (2): 10-12.

提高亚包晶钢板坯拉速对结晶器传热的影响

赵紫锋¹，张炯明¹，王新华¹，梅峰²，阮小明²

1. 北京科技大学冶金与生态工程学院，北京 100083 ；
2. 宝山钢铁股份有限公司技术中心，上海 201900 ；

收稿日期:2008-09-12 出版日期:2009-04-01 发布日期:2022-11-28
作者简介:赵紫锋(1972-)，男，博士生，板坯用保护渣和结晶器传热研究。
基金资助:
国家自然科学基金与宝钢联合资助项目(50774109)

Influence of Increasing Casting Speed of Hypoperitectic Steel Slab on Heat Transfer of Mold

Zhao Zifeng¹ , Zhang Jiongming¹ , Wang Xinhua¹ , Mei Feng² , Ruan Xiaoming²

1 School of Metallurgical and Ecological Engineering,University of Science and Technology,Beijing 100083;
2 Technical Center,Baoshan Iron and Steel Co Ltd,Shanghai 201900；

Received:2008-09-12 Published:2009-04-01 Online:2022-11-28

摘要/Abstract

摘要： 通过对提高亚包晶钢AQ钢种230 mm×1200 mm板坯拉速试验过程中结晶器冷却水参数、铜板测温等数据进行适时记录,并与数学模型及ANSYS商业软件相结合,研究了提高拉速对结晶器平均热流、局部热流、铜板温度场以及坯壳厚度的影响。结果表明,拉速由1.3m/min提高到1.5m/min时,平均热流增加0.1 MW/m²左右,宽边弯月面区域局部热流增加0.13 MW/m²,但均在合理范围内,这与采用高碱度高结晶温度的试验保护渣有关;结晶器窄/宽面平均热流比超过0.9,应适当减少结晶器锥度;宽面坯壳厚度平均减薄4 mm左右,应严格控制结晶器传热强度,以保证连铸工艺稳定和铸坯质量。

关键词: AQ钢板坯, 拉速, 结晶器, 传热

Abstract: According to real-time data recording of cold water parameters for mold and temperature of copper plate measured by thermocouple during test of increasing cast speed of hypoperitectic AQ steel grade 230 mm ×1200 mm slab, and combined with math model and ANSYS commercial software,the influence of increasing casting speed on mold average heal flux,local heat flux,temperature field of copper plate and thickness of strand shell has been studied. Results showed that with increasing casting speed from 1.3 m/min to 1.5 m/min,the average heat flux increased by about 0.1 MW/m², the local heat flux in broadside meniscus region increased by more than 0.13 MW/m²which were all in reasonable range due to using test mold powder with high basicity and high crystallizing temperature; the average ratio of heat flux of mold narrow/broad-side was 0.9 so the taper of copper plate should be reduced properly; and the average thickness of broadside strand shell reduced by about 4 mm,therefore the intensity of heat transfer of mold must be controlled strictly to ensure casting process stability and slab quality.

Key words: Steel AQ Slab, Casting Speed, Mold, Heat Transfer

赵紫锋, 张炯明, 王新华, 梅峰, 阮小明. 提高亚包晶钢板坯拉速对结晶器传热的影响[J]. 特殊钢, 2009, 30(2): 10-12.

Zhao Zifeng , Zhang Jiongming , Wang Xinhua , Mei Feng , Ruan Xiaoming. Influence of Increasing Casting Speed of Hypoperitectic Steel Slab on Heat Transfer of Mold[J]. Special Steel, 2009, 30(2): 10-12.

[1]	王玉平, 吴健博. 1000～2200 mm宽板坯连铸机结晶器流场优化与应用[J]. 特殊钢, 2024, 45(5): 85-89.
[2]	陈德, 张广军, 刘吉刚. GCr15轴承钢方坯连铸轻压下工艺优化与实践[J]. 特殊钢, 2024, 45(2): 50-55.
[3]	刘启龙, 邓勇, 李华刚, 韦如军, 曹成虎, 张敏. IF钢板坯结晶器电磁搅拌数值模拟与工艺实践[J]. 特殊钢, 2023, 44(6): 83-88.
[4]	周伟基, 姚玉东, 刘佳伟, 岳峰, 史建凯. 结晶器电磁搅拌对Q355NE Φ800 mm圆坯凝固组织及偏析的影响[J]. 特殊钢, 2023, 44(3): 64-68.
[5]	周伟基, 姚玉东, 刘佳伟, 岳峰, 张磊. Φ800 mm圆坯Q355NE凝固传热数值模拟和工艺实践[J]. 特殊钢, 2023, 44(2): 7-11.
[6]	林鹏, 许正周, 印传磊, 张洪才, 翟万里, 许光乐. 60Si2Mn弹簧钢150 mm x 150 mm铸坯缺陷分析与工艺优化[J]. 特殊钢, 2022, 43(5): 59-62.
[7]	齐新霞, 贾琦. Q460钢3 250 mm x 150 mm宽板坯凝固传热数值模拟研究和应用[J]. 特殊钢, 2022, 43(4): 1-4.
[8]	杨文轩, 王勇, 高锦国, 刘威, 杨树峰, 李京社. 1 500 mm x230 mm板坯结晶器液面波动与卷渣行为水力学模型试验和应用[J]. 特殊钢, 2022, 43(2): 21-26.
[9]	韩秀丽, 闫晓鹏, 刘磊, 赵凯, 王程, 杜亮. 连铸结晶器保护渣渣膜传热特性研究进展[J]. 特殊钢, 2021, 42(6): 6-13.
[10]	张越, 吕泽安, 马建祎, 钟骞, 王占忠, 彭峰. 轻压下和拉速对42CrMo钢410 mm x 530 mm铸坯轧成Φ195 mm材的低倍和中心C偏析的影响[J]. 特殊钢, 2021, 42(4): 35-38.
[11]	党爱国, 钟保军, 田新中, 李永超. 160 mm x 160 mm连铸坯结晶器电磁搅拌对钢液流场影响的数值模拟[J]. 特殊钢, 2020, 41(6): 6-11.
[12]	王东兴, 杨伟勇, 汪春梅, 陶群南, 黄雁, 左小坦. 含铌钢HRB400Nb 180 mm x 180 mm铸坯角部裂纹分析及改进工艺[J]. 特殊钢, 2020, 41(5): 25-28.
[13]	郎炜旳, 翟俊, 陈洋, 李晓军, 常国栋. 不锈钢连铸板坯结晶器钢液喂稀土丝工艺试验研究[J]. 特殊钢, 2020, 41(3): 35-38.
[14]	谢集祥, 罗钢, 刘浏, 汪成义. Q235B钢板坯连铸凝固传热行为的数值模拟计算[J]. 特殊钢, 2020, 41(2): 10-14.
[15]	张洪才, 林鹏, 许正周, 印传磊, 许光乐. 钢球用钢Φ380mm连铸圆坯表面裂纹原因分析及工艺改进[J]. 特殊钢, 2020, 41(1): 39-42.