1Cr18Ni9Ti不锈钢1.2 t锭电渣重熔过程[Ti]烧损控制的实践

特殊钢 ›› 2012, Vol. 33 ›› Issue (3): 38-40.

1Cr18Ni9Ti不锈钢1.2 t锭电渣重熔过程[Ti]烧损控制的实践

何润¹，周立新¹，胡长伟²，张洲²

湖北新冶钢有限公司1技术中心;2炼钢事业部，黄石435001

收稿日期:2011-11-30 出版日期:2012-06-01 发布日期:2022-10-13
作者简介:何润(1982-),男，硕士，工程师,2006年武汉科技大学毕业，高温合金品种开发，特种冶炼与锻造技术。

Practice of Control for [Ti] Melting Loss during Stainless Steel 1Cr18Ni9Ti 1.2 t Ingot ESR Process

He Run¹, Zhou Linxin¹, Hu Changwei²， Zhang Zhou²

1 Technical Center, 2 Facility Department of Steelmaking, Hubei Xinyegang Co Ltd, Huangshi 435001

Received:2011-11-30 Published:2012-06-01 Online:2022-10-13

摘要/Abstract

摘要： 统计分析了1Cr18Ni9Ti钢1.2 t锭电渣重熔过程母材中的Ti含量-[Ti](0.586%～0.839%Ti)、渣中TiO₂含量(2.1%～4.8%TiO₂)和填充比(0.2～0.4)对[Ti]平均烧损值的影响。结果得出,电渣重熔过程电渣锭下部[Ti]的烧损较上部严重;随母材[Ti]的提高,电渣锭中平均烧损[Ti]降低;随渣中TiO₂含量-(TiO₂)提高,电渣锭下部[Ti]的平均烧损β值增加,而电渣锭上部β值没有明显变化,(TiO₂)不宜超过2%;提高填充比有利于抑制[Ti]烧损。

关键词: 1Cr18Ni9Ti不锈钢, 1.2 t锭电渣重熔, [Ti]烧损 , 工艺实践

Abstract: The effect of Ti content in steel lCrl8Ni9Ti electrode- [Ti] (0. 586% ~0. 839% ) , TiO₂ content in slag- (TiO₂) (2. 1% ~4. 8% ) and packed ratio (0. 2 ~0. 4) (area of electrode / area of mold) on average melting loss of [Ti] during 1. 2 t ESR process is counted and analyzed. It is obtained that during electroslag remelting (ESR) process the melting loss of [Ti] at lower part of ESR ingot is larger than that at upper part； with increasing [ Ti] in electrode, the average melting loss of [Ti] decreases； and with increasing TiO₂ content in slag- (TiO₂) , the p value of average melting loss of [Ti] at lower part of ESR ingot increases, while the β value of that at upper part of ESR ingot has not obvious change, the (TiO₂) larger than 2% is not available； and increasing packed ratio is available to inhibit melting loss of [Ti].

Key words: Stainless Steel 1Cr18Ni9Ti, 1. 2 t Ingot ESR, Melting Loss of [Ti], Practice of Process

何润, 周立新, 胡长伟, 张洲. 1Cr18Ni9Ti不锈钢1.2 t锭电渣重熔过程[Ti]烧损控制的实践[J]. 特殊钢, 2012, 33(3): 38-40.

He Run, Zhou Linxin, Hu Changwei, Zhang Zhou. Practice of Control for [Ti] Melting Loss during Stainless Steel 1Cr18Ni9Ti 1.2 t Ingot ESR Process[J]. Special Steel, 2012, 33(3): 38-40.

[1]	郭键, 和红杰, 韩清连, 卢登攀. 中间包双挡渣墙对冷镦钢Q10B21-C夹杂物去除工艺实践[J]. 特殊钢, 2020, 41(5): 34-37.
[2]	王春梅, 黄永建, 李双江. 300 mm x360 mm连铸坯生产Φ80 mm非调质钢38MnVS6工艺实践[J]. 特殊钢, 2019, 40(5): 21-23.
[3]	王之香, 高建兵, 王玉玲, 王育田, 张锦文. 时速350 km中国标准动车组车轴用钢DZ2的生产工艺实践[J]. 特殊钢, 2019, 40(1): 19-22.
[4]	高菊, 丁志军, 李辉. 提高齿轮钢8620RH( K)末端淬火内控符合率的工艺实践[J]. 特殊钢, 2018, 39(5): 28-31.
[5]	丰年. 120t BOF-LF-VD-CC流程生产磨球钢B2的工艺实践[J]. 特殊钢, 2018, 39(2): 17-20.
[6]	宋延成, 刘吉刚. 150t转炉脱磷炉渣控制工艺的实践[J]. 特殊钢, 2018, 39(1): 44-47.
[7]	陈均, 江南红, 龚洪君, 张彦恒, 曾建华. 200t顶底复吹转炉半钢冶炼深脱磷工艺实践[J]. 特殊钢, 2017, 38(6): 40-44.
[8]	万长杰, 申丽娟, 刘梅, 赵天力. 高碳微合金非调质钢C70S6的开发和工艺实践[J]. 特殊钢, 2017, 38(5): 31-33.
[9]	冯文甫, 郭键, 叶凡新, 曹红波, 陈月光. 60t AOD兑脱磷铁水一步法冶炼0Crl2Mnl5NiCuN不锈钢的工艺实践[J]. 特殊钢, 2017, 38(4): 35-37.
[10]	祁庆花, 赵子文, 韩文科, 杨德生. 30t EAF-LF-VD-13t 铸锭流程生产14Cr1Mo钢的工艺实践[J]. 特殊钢, 2017, 38(2): 19-22.
[11]	叶凡新, 冯文甫, 郭志彬, 王晓亮, 曹红波, 吴广海. 60t AOD-LF-CCM 流程冶炼清洁球用超低[C+N]不锈钢0Cr13的工艺实践[J]. 特殊钢, 2017, 38(2): 23-25.
[12]	叶凡新, 冯文甫, 郭志彬, 王晓亮, 曹红波, 吴广海. 60 t AOD全铁水精炼400系不锈钢热补偿技术的工艺实践[J]. 特殊钢, 2016, 37(6): 44-46.
[13]	张振申, 程官江, 王新志, 王中岐, 夏志升. 超低碳钢150 t转炉冶炼过程超低硫的控制和工艺实践[J]. 特殊钢, 2016, 37(6): 47-51.
[14]	薛正学, 郑亚旭, 姜方, 都郢祁, 郭保善, 林鹏, 史成斌. 825合金抽锭式快速电渣重熔锭表面质量和Ti烧损的控制[J]. 特殊钢, 2016, 37(4): 37-40.
[15]	黄周华, 阙宗华, 董军. 100t DC EAF-LF-VD-CC流程硫易切削钢SAE1144的生产实践[J]. 特殊钢, 2016, 37(2): 39-40.