盾构机轴承套圈用钢42CrMo连续加热奥氏体晶粒长大模型

特殊钢 ›› 2014, Vol. 35 ›› Issue (6): 57-59.

盾构机轴承套圈用钢42CrMo连续加热奥氏体晶粒长大模型

郑禹¹，姜培扬¹，张豪臻¹，周乐育²，张朝磊²，刘雅政²

北京科技大学1高等工程师学院;
2材料科学与工程学院，北京100083

收稿日期:2014-06-23 出版日期:2014-12-01 发布日期:2022-08-20
通讯作者: 周乐育
作者简介:郑禹(1993-),男，本科生(北京科技大学)，材料成型与控制工程。
基金资助:
“十二五”国家863计划项目(No. 2012AA03A503)；
北京科技大学本科生创新计划项目(国家级，No. 14180008)

Model of Austenite Grain Growth during a Continuous Heating Process of Steel 42CrMo for Bearing Ring of Shield Tunneling Machine

Zheng Yu¹, Jiang Peiyang¹ , Zhang Haozhen¹, Zhou Leyu², Zhang Chaolei² ， Liu Yazheng²

1 School of Advanced Engineering,
2 School of Materials Science and Engineering,University of Science and Technology, Beijing 100083

Received:2014-06-23 Published:2014-12-01 Online:2022-08-20

摘要/Abstract

摘要： 基于盾构机轴承套圈用42CrMo钢的等温奥氏体长大模型,并利用相加性原则,建立了该钢在连续加热过程中的奥氏体晶粒长大模型。该建立的模型考虑了原始奥氏体晶粒尺寸的影响,包括建立的在间隔时间（t_i-1,t_i）内晶粒尺寸d_i模型以及保温时间t_i^*模型。通过Gleeble-1500试验机,测试了42CrMo钢（/%:0.40C,0.23Si,0.60Mn,0.016P,0.001S,1.08Cr,0.22Mo）锻坯（终锻温度850℃）以100℃/s加热1000~1300℃,水冷后的奥氏体晶粒尺寸。结果表明,奥氏体化温度由1000℃增加至1100℃时,42CrMo钢奥氏体晶粒尺寸由16.3μm增至30.3μm;加热温度超过1100℃,晶粒尺寸急剧增加,1300℃时,奥氏体晶粒尺寸为112.5μm;奥氏体晶粒尺寸的模型预测值与实测值吻合较好。

关键词: 轴承套圈用钢42CrMo, 连续加热, 奥氏体, 晶粒长大, 模型

Abstract: Based on the model of isothermal austenite grain growth of steel 42CrMo for bearing ring of shield tunneling machine, the model of austenite grain growth during continuous heating process of steel has been established by using the principle of additivity. The effect of original austenite grain size is considered in the established model, it is included in established models of grain size d_i and soaking time t_i^* during interval time (t_i-1,t_i). With using Gleeble-1500 thermal simulation machine the austenite grain size of forged billet ( finishing forging at 850 ℃)of steel 42CrMo (/% : 0. 40C, 0. 23Si, 0. 60Mn, 0. 016P, 0. 001S, 1. 08Cr, 0. 22Mo) with 100 ℃/s heated to 1000-1300 °C and water cooling has been tested and measured. Results show that with increasing austenitizing temperature from 1 000 ℃ to 1 100 ℃ the grain size of austenite in steel 42CrMo increases from 16. 3 μm to 30. 3 μm, the grain size of steel rapidly increases as heating temperature is more than 1100 °C and the austenite grain size in steel heating at 1300 °C is 112. 5 μm； the predicted value by model and measured value of austenite grain size in steel are better identical.

郑禹, 姜培扬, 张豪臻, 周乐育, 张朝磊, 刘雅政. 盾构机轴承套圈用钢42CrMo连续加热奥氏体晶粒长大模型[J]. 特殊钢, 2014, 35(6): 57-59.

Zheng Yu, Jiang Peiyang , Zhang Haozhen, Zhou Leyu, Zhang Chaolei, Liu Yazheng. Model of Austenite Grain Growth during a Continuous Heating Process of Steel 42CrMo for Bearing Ring of Shield Tunneling Machine[J]. Special Steel, 2014, 35(6): 57-59.

[1]	耿鑫, 姜周华, 葛春钰, 辛光瀚. 渣系组元对电渣重熔核级316H不锈钢中氢含量的影响[J]. 特殊钢, 2024, 45(4): 83-88.
[2]	谭庆丰, 贾红帅, 王宇, 闫占东, 运永佳, 王玉辉, 郑继辉. 核电站堆内构件用奥氏体不锈钢冷拉棒材的研制[J]. 特殊钢, 2024, 45(3): 5-9.
[3]	刘增山, 冯亮花, 康小兵. 基于PSO-SVM模型的转炉终点预测[J]. 特殊钢, 2024, 45(3): 27-32.
[4]	章东海, 徐荣川, 郭畅, 许勇, 张晓磊, 潘明旭. AOD法冶炼护环用奥氏体不锈钢1Mn18Cr18N[J]. 特殊钢, 2024, 45(2): 46-49.
[5]	徐浩, 刘建华, 刘洪波, 刘颖, 李民, 何杨. 高锰奥氏体低温钢发展现状、成分设计及热处理焊接工艺分析[J]. 特殊钢, 2024, 45(2): 8-17.
[6]	田帅, 张雪凌, 刘振宝, 王晓辉, 王长军, 孙永庆, 杨志勇, 齐越. Nb微合金化对Cr-Co-Ni-Mo系超高强度不锈钢腐蚀疲劳性能的影响[J]. 特殊钢, 2024, 45(1): 103-110.
[7]	吴晓涵, 宋志刚, 何建国, 丰涵, 郑文杰, 朱玉亮. N含量对S32750双相不锈钢中二次奥氏体析出行为的影响[J]. 特殊钢, 2024, 45(1): 18-22.
[8]	杨婷, 段路昭, 刘需, 白丽娟, 张云飞, 孙力. 20CrMnTiH连续冷却相变预测模型[J]. 特殊钢, 2024, 45(1): 82-86.
[9]	陈君, 苏春阳, 姜亚清. 基于多元线性回归的转炉石灰加入量计算模型[J]. 特殊钢, 2024, 45(1): 42-47.
[10]	徐锋, 孙强, 陆瑞. 冷处理对S46500超高强度不锈钢组织和性能的影响[J]. 特殊钢, 2023, 44(6): 107-111.
[11]	郑冰, 徐东, 王怡群, 王学玺, 赵红阳, 巨东英. 34CrNi3MoV钢奥氏体晶粒长大模型验证与应用[J]. 特殊钢, 2023, 44(6): 101-106.
[12]	薛润东, 赵志毅, 费爱庚. 冷加工对CN-1515奥氏体不锈钢包壳管亚结构的影响[J]. 特殊钢, 2023, 44(5): 107-112.
[13]	张威, 王旗, 王丽君, 李建民. S31254超级奥氏体不锈钢凝固相转变的热力学分析[J]. 特殊钢, 2023, 44(4): 8-14.
[14]	唐郑磊, 王福明, 于乔木, 郭然, 许少普, 张阳. 热处理工艺对水电站用钢SXQ500/550DZ35奥氏体晶粒的影响[J]. 特殊钢, 2023, 44(3): 104-108.
[15]	苏梁, 弓硕, 王福明. 预热处理工艺对SCr420H齿轮钢高温渗碳奥氏体晶粒长大行为的影响[J]. 特殊钢, 2023, 44(3): 74-83.