120t LD-LF-RH-CC全流程钢水氮含量控制技术研究和工艺实践

特殊钢 ›› 2016, Vol. 37 ›› Issue (2): 49-53.

120t LD-LF-RH-CC全流程钢水氮含量控制技术研究和工艺实践

陈均，曾建华，陈永，陈天明

攀钢集团研究院有限公司，钒钛资源综合利用国家重点实验室，攀枝花 617000

收稿日期:2015-11-23 出版日期:2016-04-01 发布日期:2022-08-08
作者简介:陈均(1986-)，男，硕士生(北京科技大学)，工程师，2009 年内蒙古科技大学(本科)毕业，炼钢工艺优化研究。

Study and Process Practice of Control Technique of Nitrogen Content in Liquid during 120t LD-LF-RH-CC Whole Flowsheet

Chen Jun , Zeng Jianhua , Chen Yong , Chen Tianming

State Key Laboratory of Vanadium and Titanium Comprehensive Utilization,Pangang Group Research Institute Co Ltd, Panzhihua 617000

Received:2015-11-23 Published:2016-04-01 Online:2022-08-08

摘要/Abstract

摘要： 针对攀钢重点品种钢氮含量偏高的问题,通过调研,确定了转炉终点钢水氮含量高、出钢过程增氮严重、精炼结束至中间包增氮严重是导致氮含量偏高的主要原因,提出“转炉低氮钢冶炼”、“两步脱氧控制出钢过程增氮”、“双氩封长水口保护浇注”等氮含量控制的关键技术,可将转炉终点钢水氮含量平均控制在13×10^-6以内,出钢过程及精炼结束至中间包增氮控制在5×10^-6以内。应用结果表明,板坯大梁钢、电工钢、IF钢成品氮含量分别为30.3×10^-6、18.2×10^-6、16.3×10^-6,方坯重轨钢和帘线钢成品氮含量平均为40.8×10^-6、38.2×10^-6,使攀钢低氮品种钢氮含量控制水平得到了大幅度的提升。

关键词: 120t LD-LF-RH-CC流程, 氮含量控制, 转炉终点, 增氮, 长水口

Abstract: According the issue of nitrogen content in key steel grades being on the high side at Pangang, by survey and study it is defined that the main factors led to nitrogen being on the high side are the LD end nitrogen content in liquid being on the high side, serious pick-up of nitrogen during tapping and serious pick-up of nitrogen in the process from end refining to tundish, and the key technique to control o£ nitrogen in liquid is put forward including "LD low nitrogen blowing" ,"two-step deoxidation to control pick-up of nitrogen in tapping process" and "double argon sealing long nozzle shielding casting" etc. technique, it shall be to control the average LD end nitrogen in liquid no more than 13 x 10^-6, and the average pick-up of nitrogen in liquid during tapping and end refining process to tundish no more than 5 x 10^-6. Application results show the nitrogen content in finished products of beam steel slab, electrical steel and IF steel is respectively 30.3 x 10^-6 , 18.2 x 10^-6 and 16.3 x 10^-6 , and the average nitrogen content in finished products of heavy rail steel and tire cord steel is respectively 40. 8 x 10-6 and 38.2 x 10^-6 to greatly improve the control level of nitrogen content in low-ni- trogen steel grades at Pangang.

Key words: 120t LD-LF-RH-CC Flowsheet, Control of Nitrogen Content in Steel, LD Endpoint, Pick-up of Nitrogen, Long Nozzle

陈均, 曾建华, 陈永, 陈天明. 120t LD-LF-RH-CC全流程钢水氮含量控制技术研究和工艺实践[J]. 特殊钢, 2016, 37(2): 49-53.

Chen Jun , Zeng Jianhua , Chen Yong , Chen Tianming. Study and Process Practice of Control Technique of Nitrogen Content in Liquid during 120t LD-LF-RH-CC Whole Flowsheet[J]. Special Steel, 2016, 37(2): 49-53.

[1]	张宇迪, 刘建华, 何杨, 李巍, 林俊宇, 陈修君, 毕胜. 增氮析氮法去除钢中夹杂物工艺实践[J]. 特殊钢, 2023, 44(6): 53-57.
[2]	隋亚飞, 张丽琴, 周军军, 刘彰. 超低碳搪瓷钢中氮的控制及其对夹杂物的影响[J]. 特殊钢, 2020, 41(4): 11-14.
[3]	张增武. 10Cr21Mn16NiN不锈钢冶炼与连铸生产实践[J]. 特殊钢, 2020, 41(3): 47-50.
[4]	郭飞虎, 仇圣桃, 乔家龙, 刘磊. 无取向电工钢冶炼过程氧含量控制[J]. 特殊钢, 2019, 40(4): 38-42.
[5]	陈均, 曾建华, 李平凡, 杨森祥, 梁新腾. 120 t转炉半钢增硅热补偿技术研究及应用[J]. 特殊钢, 2018, 39(6): 28-32.
[6]	周莉, 曹晓恩, 杨吉春. 增氮节镍型316奥氏体不锈钢的耐冲蚀性能[J]. 特殊钢, 2018, 39(5): 62-66.
[7]	冯文甫, 郭键, 叶凡新, 曹红波, 陈月光. 60t AOD兑脱磷铁水一步法冶炼0Crl2Mnl5NiCuN不锈钢的工艺实践[J]. 特殊钢, 2017, 38(4): 35-37.
[8]	李国丰, 贺冰林, 王学义, 刘义仁. Φ210~310 mm管坯连铸长水口保护浇注的工艺实践[J]. 特殊钢, 2016, 37(6): 38-40.
[9]	阮飞, 赵凤光, 富晓阳, 刘卓承, 杨吉春, 张捷宇. 异型坯连铸长水口浸入深度对36 t中间包流场和温度场的影响[J]. 特殊钢, 2015, 36(1): 9-13.
[10]	杜和平, 杨志才. 150 t钢包炉(LF)精炼过程控制钢水增氮的工艺实践[J]. 特殊钢, 2015, 36(1): 25-27.
[11]	岳江波, 甘晓龙, 陈子宏. 真空感应炉熔炼合金钢时用氮化物增氮的试验研究[J]. 特殊钢, 2012, 33(6): 1-4.
[12]	吕学飞, 丛花越, 张宇, 王勇胜, 乔兵. 45 t LF(VD)精炼钒氮非调质钢的增氮工艺[J]. 特殊钢, 2009, 30(2): 46-47.
[13]	王海兵. 92 t EAF-LF冶炼20G钢液的氮含量控制[J]. 特殊钢, 2005, 26(6): 59-60.