含P高强度IF钢酸轧拉矫断带分析和工艺改进

特殊钢 ›› 2019, Vol. 40 ›› Issue (2): 53-56.

含P高强度IF钢酸轧拉矫断带分析和工艺改进

李俊生¹ 薛仁杰¹ 马娥²，曹晓恩¹，罗翔³

1河钢集团邯钢公司技术中心汽车家电板研发中心，邯郸056015；
2河钢集团钢研总院，石家庄050023 ；
3北京科技大学工程技术研究院，北京100083)

收稿日期:2018-10-11 出版日期:2019-04-01 发布日期:2022-05-19
作者简介:李俊生(1973-),男，高级工程师，主要从事汽车板产品研发。

Analysis on Strip Fracture of High Strength IF Steel Containing Phosphorus During Straightening in Pickling & Rolling and Process Improvement

Li Junsheng¹ ,Xue Renjie¹ ,Ma E² ,Cao Xiaoen¹ ， Luo Xiang³

1 Automotive & Appliance Sheet R & D Center, Technique Center, Handan Company, Hesteel Group, Handan 056015;
2 Technology Research Institute, Hesteel Group, Shijiazhuang 050023;
3 Beijing University of Science and Technology,Engineering Technology Research Institute,Beijing 100083

Received:2018-10-11 Published:2019-04-01 Online:2022-05-19

摘要/Abstract

摘要： 采用化学成分、扫描电镜及俄歇电子能谱等手段分析了含P高强IF钢HC250IF酸轧拉矫断带原因,明确B含量低未能抑制P的晶界偏聚,形成的FeTiP或Fe₃P化合物导致晶界脆性是酸轧拉矫断带的根本原因。通过优化加硼工艺、提高钢中B含量从0.0002%～0.0007%升至0.000 8%～0.0012%、严格控制N含量≤30×10^-6、RH添加硼铁后真空净循环≥8 min保证成分均匀性的措施可有效避免含P高强IF钢酸轧拉矫断带

关键词: 含P高强IF钢, 断带, 磷偏聚, 硼

Abstract: The chemical composition, scanning electron microscopy and auger electron spectroscopy were used to analyze the reasons of the strip fracture of high strength IF steel HC250IF containing phosphorus during straightening in pickling & rolling process. It is confinned that the content of B is too low and the segregation of P at grain boundary could not be inhibited,and the FeTiP or Fe3P compound formed at the grain boundary resulting in brittleness is the basic cause of strip fracture. By optimized process for adding boron, increasing the content of B from 0.0002% 〜0.0007% to 0.0008% ~ 0.0012% , controlling strictly the content N≤ 30 x 10^-6 and vacuum cycle for 8 min after adding the boron iron in RH process, it is to ensure the uniformity of the composition, the strip fracture of high strength IF steel containing phosphorus during straightening in pickling & rolling process can be effectively avoided.

Key words: High Strength IF Steel Containing Phosphorus, Strip Fracture, Phosphorus Segregation, Boron ,

李俊生, 薛仁杰, 马娥, 曹晓恩, 罗翔. 含P高强度IF钢酸轧拉矫断带分析和工艺改进[J]. 特殊钢, 2019, 40(2): 53-56.

Li Junsheng , Xue Renjie , Ma E , Cao Xiaoen , Luo Xiang. Analysis on Strip Fracture of High Strength IF Steel Containing Phosphorus During Straightening in Pickling & Rolling and Process Improvement[J]. Special Steel, 2019, 40(2): 53-56.

[1]	李阳, 赵广迪, 臧喜民, 姜昊源, 王兆宇. B对Fe-Cr-B-C合金热处理后显微组织和强韧性的影响[J]. 特殊钢, 2024, 45(5): 25-33.
[2]	曾莉, 王斌, 徐梅, 张威. 硼对奥氏体不锈钢高温氧化性能的作用机理[J]. 特殊钢, 2023, 44(2): 61-64.
[3]	陈修君, 毕胜, 周伟基, 姚玉东, 王鑫. 10B21冷镦钢冶炼工艺优化实践[J]. 特殊钢, 2022, 43(4): 63-65.
[4]	罗应明, 王九清, 庞辉勇, 张朋, 蒙耀华, 赵燕青. 水电站用800 MPa级低焊接裂纹敏感性高强钢板SX780CF的开发[J]. 特殊钢, 2022, 43(3): 21-24.
[5]	王芝林, 何国宁, 高建鹏, 贾羽, 赵海东. 20CrMnTiH钢中残余硼对末端淬透性的影响及工艺控制[J]. 特殊钢, 2022, 43(2): 40-43.
[6]	王斌, 张寿禄, 赵振铎. 热处理工艺对2%硼304B7不锈钢组织性能的影响[J]. 特殊钢, 2021, 42(3): 83-87.
[7]	李小明. 渗硼工艺对汽车用45CrNiMoV热锻模具钢性能的影响[J]. 特殊钢, 2021, 42(1): 57-60.
[8]	仝中伟. 硼对S31254不锈钢固溶处理过程第二相溶解行为的影响[J]. 特殊钢, 2020, 41(4): 71-74.
[9]	王利军, 李永超, 王成杰, 阮士朋, 王宁涛, 张鹏宁. 铌-钛微合金化中碳硼钢连铸坯的高温力学性能[J]. 特殊钢, 2020, 41(3): 67-71.
[10]	李建新, 王飞, 翟羽佳, 王瑞. 热处理对40CrMnSiB低合金超高强度钢组织和性能的影响[J]. 特殊钢, 2020, 41(2): 47-49.
[11]	黄镇. 终轧温度对热轧中碳含硼钢40B实际晶粒度的影响[J]. 特殊钢, 2020, 41(1): 58-60.
[12]	赵燕青, 孙力, 刘宏强, 王九清, 安会龙, 罗应明, 车金锋. 硼对780 MPa低碳贝氏体钢组织和力学性能的影响[J]. 特殊钢, 2018, 39(2): 65-67.
[13]	段路昭, 苏玉辉, 崔娟, 李永超, 刘超. 碳和硼含量对低碳冷镦钢连铸坯高温力学性能的影响[J]. 特殊钢, 2015, 36(4): 63-65.
[14]	王凌燕, 于旭光, 张翼, 刘丹, 王俊帅. 温度对33EH高性能烧结钗铁硼永磁体磁性能的影响[J]. 特殊钢, 2015, 36(1): 45-48.
[15]	王黎, 吴涛. 硼对低温球罐用钢07MnNiMoVDR 50 mm板组织与力学性能的影响[J]. 特殊钢, 2013, 34(6): 59-61.