轻压下对20CrMnTiH钢240mm×240mm铸坯中心碳偏析和低倍组织的影响

特殊钢 ›› 2020, Vol. 41 ›› Issue (5): 64-67.

轻压下对20CrMnTiH钢240mm×240mm铸坯中心碳偏析和低倍组织的影响

李荣¹, 晁霞², 郭江¹

1济源职业技术学院冶金与化学工程系，济源459000；
2河南济源钢铁(集团)有限公司，济源459000

收稿日期:2020-04-28 出版日期:2020-10-01 发布日期:2022-05-06
作者简介:李荣(1980-),女，硕士(2005年内蒙古大学)，副教授， 2002年包头钢铁学院(本科)毕业,冶金工艺技术研究、
基金资助:
河南省自然科学基金项目资助(19B450003)

Effect of Soft Reduction on Central Carbon Segregation and Macrostructure of 240 mm x 240 mm Casting Bloom of Steel 20CrMnTiH

Li Rong¹ , Chao Xia² , Guo Jiang¹

1 Department of Metallurgical and Chemical Engineering, Ji yuan Vocational and Technical College, Jiyuan 459000 ；
2 Henan Jiyuan Iron and Steel ( Group) Co Ltd, Jiyuan 459000)

Received:2020-04-28 Published:2020-10-01 Online:2022-05-06

摘要/Abstract

摘要： 试验研究了单辊轻压下量（0～14 mm）和压下位置（1^#～7^#）对低碳钢20CrMnTiH 240 mm×240 mm铸坯低倍组织和中心碳偏析的影响。结果表明,从3^#拉矫辊开始压下,最大压下量9 mm,低倍无缩孔比例上升12.3%,中心疏松1.0级比例和中心碳偏析无明显改善;从2^#拉矫辊开始压下,最大压下量1 1 mm,中心疏松1.0级比例和无缩孔比例下降,中心碳偏析合格率提升14.2%;从1^#拉矫辊开始压下,最大压下量14 mm,中心疏松1.0级和无中心缩孔比例均为100%,中心碳偏析合格率达到71.4%。综合分析得出,20CrMnTiH 240 mm×240mm铸坯在拉速0.85 m/min、结晶器搅拌300 A、5 Hz、单辊轻压下量14 mm时,铸坯中心碳偏析和低倍组织最佳。

Abstract: The effect of single roll soft reduction (0〜14 mm) and reduction position ( 1^# ~ 7^#) on inacrostructure and central carbon segregation of 240 mm x 240 mm casting bloom of low carbon steel 20CrMnTiH has been tested and studied. Results show that as from roll No. 3 reduction and maximum soft reduction 9 mm, the ratio of the without shrinkage cavity increases by 12.3% and the ratio of center porosity 1.0 rating and center carbon segregation do not improve obviously ；as from roll No. 2 reduction with maximum soft reduction 1 1 mm, the ratios of center porosity 1.0 rating and the without shrinkage cavity decrease, and the ratio of center carbon segregation increases by 14. 2% ； as from roll No. 1 reduction and the maximum soft reduction 14 mm, the ratios of center porosity 1.0 rating and without shrinkage cavity are up to 100% , and the ratio of center carbon segregation is 71.4% . By comprehensive analysis it is obtained that with casting speed 0.85 m/min, mold stirring 300 A and 5 Hz, the central carbon segregation and macrostructure of steel 20CrMnTiH 240 mm x 240 mm casting billet are better by single roll soft reduction 14 mm.

李荣, 晁霞, 郭江. 轻压下对20CrMnTiH钢240mm×240mm铸坯中心碳偏析和低倍组织的影响[J]. 特殊钢, 2020, 41(5): 64-67.

Li Rong , Chao Xia , Guo Jiang. Effect of Soft Reduction on Central Carbon Segregation and Macrostructure of 240 mm x 240 mm Casting Bloom of Steel 20CrMnTiH[J]. Special Steel, 2020, 41(5): 64-67.

参考文献

[1]陈俊儒.张慧,王明林.等.特殊钢连铸大方坯内部质量问题研究现状[J].铸造技术,2019.40(8) ：874-878.
[2]杜东福.赵喜庆.张建元，等.提高20crmntih齿轮钢冶金质量的工艺实践[j]特殊钢.2018,39(2)：34-37.
[3]王羽挪.王庆娟，徐李军.等.轻压下技术在板坯连铸生产中的应用[J].钢铁研究学报,2012.24(3):1-7.
[4]周伟基.沙玉峰.路辉，等,GCrl5连铸大方坯凝固终点及末端的大压下区间[J].钢铁,2018,253( 1 ):4145.
[5]闫卫兵，郭旭东.宣钢小方坯连铸应用轻压下技术试验[J].河北冶金.2018(2) ：5-9.
[6]赵军普，刘浏,范建文，等.轻压下技术及其在连铸中的研究与应用[J].材料导报,2018.30(8):57-61.
[7]Luo S,Zhu M Y and Ji C. Theoretical Model for Determining Optimum Soft Reduction Zone of Continuous Casting Steel [J]. Ironmaking & Steelmaking,2014 ,41(3) ：233-239.
[8]Ji C, Luo S and Zhu M Y. Analysis and Application of Soft Reduction Amount for Bloom Continuous Casting Process[ J] - ISIJ International ,2014 ,54(3 ) ：504-510.
[9]Liu K,Sun Q and Zhang J,et al. A Study on Quantitative Evaluation of Soft Reduction Amount for CC Bloom by Thermo-Mechanical FEM Model [J] . Metallurgical Research & Technology ,2016,113(5)： 504-559.
[10]Sun H and Zhang J. Study on the Macrosegregation Behavior for the
Bloom Continuous Casting： Model Development and Validation [ J J.
Metallurgical & Materials Transactions B, 2014,45 ( 3 ) ： 1133-1149.
[11]曾杰，陈伟庆，曹长法.等.轻压下对82B钢矩形坯内部质量的影响[J].炼钢,2015,31(4) ：63-66.
[12]李茂印，杨树峰、李京社，等.轻压下调整对模具钢宽厚板坯中心质戢的优化[J].钢铁,2017,52(12) ：3641,
[13]林大帅，李晓斐，张文涛，等.轻压下对C610L连铸板坯内部品质的改善[J].炼钢,2019,35(5):50-53.
[14]李德军，廖相巍，于赋志，等.轻压下对高碳钢小方坯内部质量的影响 [J].上海金属,2017,39(6):4549.
[15]李德军，李泽林，赵志刚，等.单辗轻压下对高碳钢SWRH72B 180 mm x 180 mm铸坯内部质量的影响[J].特殊钢,2017, 38 (6) : 33-36.