凝固组织对GCr15轴承钢220 mm×260 mm连铸坯中心偏析的影响

特殊钢 ›› 2021, Vol. 42 ›› Issue (1): 50-56.

所属专题：轴承钢

凝固组织对GCr15轴承钢220 mm×260 mm连铸坯中心偏析的影响

左欢¹,杨祝英¹,安航航²

1. 天津工业职业学院 2. 北京科技大学钢铁共性技术协同创新中心

出版日期:2021-02-01 发布日期:2022-04-08
作者简介:左欢(1982-),男，工程师,2007年内蒙古科技大学(本科)毕业，炼钢技术研究。E-mail：286870211@qq.com

Effect of Solidification Structure on Center Segregation of 220 mm x 260 mm Casting Bloom of Bearing Steel GCrl5

Zuo Huan¹, Yang Zhuying¹, An Hanghang²

1 Tianjin Polytechnic College, Tianjin 056404 ； 2 Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083

Published:2021-02-01 Online:2022-04-08

摘要/Abstract

摘要： 铸坯高中心等轴晶率及小的二次枝晶臂间距有利于降低高碳钢M+E-EMS连铸坯中心偏析。通过建立GCr15钢220 mm×260 mm连铸坯耦合有限元-元胞自动机模型(CAFE)及二次枝晶臂间距(SDAS)模型,研究结晶器电磁搅拌、过热度和拉速对中心等轴晶率及二次枝晶臂间距的影响。结果表明,相比于拉速,过热度和结晶器电磁搅拌对其影响明显。随着过热度降低及结晶器电磁搅拌强度增加,铸坯中心等轴晶率增加而二次枝晶臂间距减小,而拉速对凝固终点和中心固相率影响大。工业试验结果表明,采用结晶器与凝固末端电磁搅拌,相比于过热度35℃和拉速0.75 m/min,控制过热度小于25℃且拉速调整为0.8 m/min时,轴承钢GCr15铸坯中心等轴晶率由原27%增加至38%且二次枝晶臂间距细化,中心碳偏析指数由原1.06～1.39降至0.93～1.13。

关键词: 220 mm×260 mm铸坯, GCr15轴承钢, 中心等轴晶, 二次枝晶臂间距, 中心偏析,

Abstract: Low secondary dendrite arm spacing (SDAS) and large center equiaxed crystal ratio (ECR) are beneficial to reduce center segregation of high-carbon steel casting bloom with M + F-EMS. A Cellular Automaton-Finite Element (CAFE) coupling model and secondary dendrite arm spacing (SDAS) model of 220 mm x 260 mm casting bloom of steel GCrl5 are established to study the effects of M-EMS, superheat and casting speed on central equiaxed crystal ratio (ESR) and SDAS. It is found that ECR in the center of bloom increases with decreasing superheat and increase intensifying M- EMS, while SDAS decreases with the decrease of superheat and with the increase of M-EMS. The results reveal that M- EMS and superheat has a significant effect on center ECR compared with casting speed. Casting speed has the obvious influence on solidification end and central solid fraction in strand. Industrial test results as compared supeheat 35 ℃ and casting speed 0. 75 m/min less than superheat 25 ℃ and casting speed 0.8 m/min and with M + F-EMS, the ECR in the center of bearing steel GCrl5 bloom increases from original 27% to 38% and the SDAS is effectively refined, center carbon segregation index decreases from original 1.06 ～ 1.39 to 0.93 ～ 1.13.

左欢, 杨祝英, 安航航. 凝固组织对GCr15轴承钢220 mm×260 mm连铸坯中心偏析的影响[J]. 特殊钢, 2021, 42(1): 50-56.

参考文献

[1]黄拓，任金朝，马忠伟，等• GCrl5轴承钢 ©380 mm连铸圆坯V-偏析的宏观与微观形貌分析[J].特殊钢,2014,35(4):48- 51.
[2]Mosleh Mohsen and Bradshaw Keron. Role of Component Configuration in Evaluation of Accelerated Rolling Contact Fatigue of Ball Bearings [J]. Wear, 2011,271(10)： 2681- 2686.
[3]王海洋，滕力宏，赵阳，等.PMO作用对连铸轴承钢凝固组织及碳化物的影响 [J] .连铸,2018,43(6):32-35.
[4]张福利，袁建路,翟永臻，等.磁控电渣对It ESR锭GCrl5轴承钢凝固组织及成分偏析的影响[J].特殊钢,2019,40(4):55-58.
[5]Yin F, Hua L and Mao H, et al. Microstructural Modeling and Simulation for GCrl5 Steel during Elevated Temperature Deformation [J]. Materials and Design,2013,55(6) ：560-573.
[6]Hou Z B, Jiang F and Cheng G G. Solidification Structure and Compactness Degree of Central Equiaxed Grain Zone in Continuous Casting Billet Using Cellular Automaton-Finite Element Method [ J ]. ISU International,2012,52(7) ： 1301-1309.
[7]仲红刚，程杰,徐智帅，等.T10A高碳钢连铸坏凝固组织热模拟研究[J].上海金属,2016,38(2)： 51-54.
[8]党爱国，崔娟,李永超，等.基于有限元法对GCrl5轴承钢280 mm x325 mm铸坯凝固组织的模拟与分析[J].特殊钢,2016,37 (5):66-68.
[9]王璐,孙彦辉，焦帅，等.轴承钢大方坏二次枝晶臂间距数值模拟[J].钢铁,2018,53(7):50-59.
[10]Gaiidin C A, Desbiolles J L and Rappaz M, et al. A Three-Dimensional Cellular Automaton-Finite Element Model for the Prediction of Solidification Grain Structures [ J]. Metallurgical and Materials Transactions A, 1999,30( 12) ：3153-3165.
[11]Gandin C A, Rappazm and Tintillier R. 3-Dimensional Simulation of the Grain Formation in Investment Casting] J]. Metallurgical and Materials Transactions A, 1994,25(3) ：629-635.
[12]Mok Won Young and Thomas Brian G. Simple Model of Micro Segregation during Solidification of Steels [J]. Metall Mater Trans A, 2001,32A： 1755-1767.
[13]Yamazaki M, Natsume Y and Harada H,et al. Numerical Simulation of Solidification Structure Formation during Continuous Casting in Fe-0.7 Mass% C Alloy Using Cellular Automaton Method [J]. ISIJ International,2006,46(6) ：903-908.
[14]Mintz B. The Influence of Composition on the Hot Ductility of Steels and the Problem of Transverse Cracking [J]. ISU International, 1999,39(9):833-855.
[15]An H H, Bao Y P and Wang M,et al. High-Efficiency Continuous Casting of GCrl5 Bearing Steel Bloom Based on Cooperative Control Technique of Complex Electromagnetic Stirring and Soft Reduction [J]. Metallurgical Research & Technology ,2019,116(6) ： 1 -11.

凝固组织对GCr15轴承钢220 mm×260 mm连铸坯中心偏析的影响

Effect of Solidification Structure on Center Segregation of 220 mm x 260 mm Casting Bloom of Bearing Steel GCrl5

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	孙剑, 李杰, 张彩东, 李杰, 赵海涛, 任刚. 改善弹簧钢小方坯中心偏析及线材性能工艺优化[J]. 特殊钢, 2024, 45(2): 89-90.
[2]	吴翔宇, 董丙成, 王梓菲, 田钱仁, 付建勋. La-Ce对GCr15轴承钢中夹杂物的改质效果及机理[J]. 特殊钢, 2024, 45(2): 39-45.
[3]	陈德, 张广军, 刘吉刚. GCr15轴承钢方坯连铸轻压下工艺优化与实践[J]. 特殊钢, 2024, 45(2): 50-55.
[4]	姜亚清, 陈君, 黄成钢, 李博, 李倩, 江焱锋. 中间包涂料对GCr15轴承钢洁净度的影响[J]. 特殊钢, 2024, 45(1): 61-64.
[5]	刘春伟, 张昊, 曹磊, 王国承, . VD低碱度渣对GCr15轴承钢夹杂物的影响[J]. 特殊钢, 2023, 44(6): 78-82.
[6]	肖丙政, 谢海平, 魏刚武, 孙陶安, 王海川, 邓爱军. GCr15轴承钢转炉冶炼中“C-P-T”协同控制工艺优化研究[J]. 特殊钢, 2022, 43(6): 54-59.
[7]	王仲亮, 包燕平, 顾超, 刘宇, 黄永生. 基于非铝脱氧工艺的GCr15轴承钢中Ds类夹杂物控制[J]. 特殊钢, 2022, 43(6): 8-12.
[8]	官跃辉, 张林, 张剑锋, 陆长河, 翟蛟龙, 石长民. GCr15轴承钢碳化物控制及其对压碎负荷的影响[J]. 特殊钢, 2022, 43(6): 38-41.
[9]	蒋鲤平, 徐建飞, 王昆鹏, 王郢, 王立涛, 陈廷军. 高碳铬GCr15轴承钢中镁铝夹杂物形成与控制工艺实践[J]. 特殊钢, 2022, 43(4): 41-45.
[10]	王清波, 张华, 李永超, 卢彩玲, 白瑞娟, 刘成松. 120 t LF精炼渣系对弹簧钢55SiCrA夹杂物塑性的影响[J]. 特殊钢, 2022, 43(1): 34-38.
[11]	饶金元, 张孟昀, 陈君, 赵立华, 包燕平. 轻压下改善42CrMo钢300mm × 400 mm大方坯内部质量的工艺实践[J]. 特殊钢, 2022, 43(1): 39-43.
[12]	李刚, 丁文彬, 张朝磊, 尹修刚, 姚忠. 大容积无缝气瓶用4130X钢Φ600 mm连铸圆坯研发[J]. 特殊钢, 2022, 43(1): 44-46.
[13]	郭志强. Als、N 和过热度对 Φ50～60 mm 40Mn2 钢裂纹影响分析和改进工艺[J]. 特殊钢, 2022, 43(1): 62-65.
[14]	雷应华, 刘尚潭, 张军, 郑振宇, 廖凯. 电液控制器用加 Bi - Ce 易切削不锈钢 1．4104 的开发[J]. 特殊钢, 2022, 43(1): 73-77.
[15]	李永灯, 彭俊, 唐科, 向鑫. 110SS 级别抗硫化氢应力腐蚀厚壁无缝钢管的开发[J]. 特殊钢, 2022, 43(1): 78-81.