减轻冲刷的单流通道式感应加热中间包结构优化数学模拟

特殊钢 ›› 2021, Vol. 42 ›› Issue (3): 1-06.

• 试验研究 • 下一篇

减轻冲刷的单流通道式感应加热中间包结构优化数学模拟

曾红波,艾新港,李胜利,刘海啸,宁哲,王春松

辽宁科技大学材料与冶金学院

收稿日期:2020-10-10 出版日期:2021-05-15 发布日期:2023-01-09
作者简介:曽红波(1992-),男，硕士在读 (辽宁科技大学)，钢铁冶金研究。

Mathematical Simulation on Structure Optimizing of Induction Heating Tundish with Single Flow to Reduce Scouring

Zeng Hongbo, Ai Xingang, Li Shengli, Liu Haixiao, Ning Zhe，Wang Chunsong

School of Material and Metallurgy, Liaoning University of Science and Technology, Anshan 114051

Received:2020-10-10 Published:2021-05-15 Online:2023-01-09

摘要/Abstract

摘要： 以钢厂30 t中间包为原型,设计了一种减轻包壁冲刷的"鼓肚式"单流通道感应加热中间包。采用数值模拟方法研究了"鼓肚式"感应加热中间包的钢液流动行为,探究了前腔体积对钢液流动状态的影响。研究结果表明,"鼓肚"显著减轻了中间包后腔包壁的冲刷,该"鼓肚式"中间包其平均停留时间延长3.83%~6.44%,死区体积减小5.6%~5.93%。前腔体积为1.06 m~3时,钢液平均停留时间最长。中间包水口流量分别为150 kg/min和200 kg/min时,平均停留时间最长分别为678 s和569 s;死区体积比例最小分别为5.87%和0.55%。

Abstract: Based on the prototype of 30 t tundish in a steelworks a " belly" induction heating tundish with single channel to reduce the erosion of the wall of tundish has been designed. The flow behavior of liquid steel of the " belly" induction heating tundish is studied by numerical simulation method, and the influence of the volume of the front cavity on the flow state of liquid steel is investigated. The results show that "belly'' can significantly reduce the erosion of the wall of tundish posterior cavity, the average residence time of the " belly" tundish is prolonged by 3. 83% ~ 6. 44% , and the dead zone volume decreases by 5. 6% ~5. 93% ； as the front cavity volume is 1. 06 m³, the average residence time of liquid steel is the longest； as the nozzle flow of tundish is 150 kg/min and 200 kg/min, the longest average residence time is 678 s and 569 s respectively and the minimum proportion of dead zone volume is 5. 87% and 0. 55% respectively./p>

曾红波, 艾新港, 李胜利, 刘海啸, 宁哲, 王春松. 减轻冲刷的单流通道式感应加热中间包结构优化数学模拟 [J]. 特殊钢, 2021, 42(3): 1-06.

Zeng Hongbo, Ai Xingang, Li Shengli, Liu Haixiao, Ning Zhe, Wang Chunsong. Mathematical Simulation on Structure Optimizing of Induction Heating Tundish with Single Flow to Reduce Scouring[J]. Special Steel, 2021, 42(3): 1-06.

参考文献

[1] Yan P, Amout S and Van Ende M A, et al. Steel Reoxidation by Gunning Mass and Tundish Slag [J]. Metallurgical and Materials Transactions B,2015,46(3) ： 1242-1251.
[2] Wang Q, Li B and Tsukihashi F. Modeling of a Thermo-Electromagneto-Hydrodynamic Problem in Continuous Casting Tundish with Channel Type Induction Heating [J]. ISIJ International, 2014,54 (2):311-320.
[3] 丛林，张炯明,雷少武，等.中间包感应加热的数值模拟[J]. 钢铁研究,2014,42(3):20-25.
[4] Tang H, Guo L and Wu G,et al. Hydrodynamic Modeling and Mathematical Simulation on Flow Field and Inclusion Removal in a Seven-Strand Continuous Casting Tundish with Channel Type Induction Heating [J]. Metals,2018,8(6) ：374-383.
[5] Ai X G , Han D and li S L, et al. Optimization of Flow Uniformity Control Device for Six-Stream Continuous Casting Tundish [J]. Journal of Iron and Steel Research International,2020,27 (6) ： 1035-1044.
[6] 韩东，艾新港,李胜利，等.基于温度场的17t双流中间包控流装置优化模拟[J]. 特殊钢,2019,40(5) ：7-11.
[7] 韩东，艾新港,李胜利，等.控流装置对双流中间包流动影响的模拟实验[J].辽宁科技大学学报,2019,42(2) ：85-90,
[8] Merder T. Modelling the Influence of Changing Constructive Parameters of Multi-Strand Tundish on Steel Flow and Heat Transfer] J]. Ironmaking & Steelmaking,2016,43(10) ：758-768.
[9] Siddiqui M I H and Jha P K. Numerical Investigation of Inclusion Behaviour in a Multi-Strand Tundish During Strand Blockages [J]. Journal of the Institution of Engineers,2015,96(2) ：l-8.
[10] 张硕，唐海燕,刘锦文，等.六流H型通道感应加热中间包的结构优化[J].钢铁研究学报,2019,31(9):787-794.
[11]艾新港，张书豪,李胜利，等.挡墙对H型中间包温度场影响的数学模拟研究[J].铸造技术,2015,36 (10) Q484-2489.

减轻冲刷的单流通道式感应加热中间包结构优化数学模拟

Mathematical Simulation on Structure Optimizing of Induction Heating Tundish with Single Flow to Reduce Scouring

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价