2.25Cr-1Mo-0.25V 钢148 mm 厚板尾部分层缺陷分析及控制工艺

doi:10.20057/j.1003-8620.2022-00105

特殊钢 ›› 2023, Vol. 44 ›› Issue (2): 43-47.DOI: 10.20057/j.1003-8620.2022-00105

2.25Cr-1Mo-0.25V 钢148 mm 厚板尾部分层缺陷分析及控制工艺

侯敬超¹ , 赵国昌¹ , 庞辉勇¹ , 吴艳阳¹ , 甄光楠¹ , 赵燕青²

1. 河钢集团舞钢公司，舞钢 462500;
2. 河钢集团钢研总院，石家庄 050023；

收稿日期:2022-08-20 出版日期:2023-04-01 发布日期:2023-03-27
作者简介:侯敬超(1989-)，男，硕士，工程师；E-mail：houjingchao@163.com

Analysis on Causes of Delamination Defect at 148 mm Heavy Thickness Plate Tail of 2.25Cr-1Mo-0.25V Steel and Control Process

Hou Jingchao¹ , Zhao Guochang¹ , Pang Huiyong¹ , Wu Yanyang¹ , Zhen Guangnan¹ , Zhao Yanqing²

1. Hesteel Group Wugang Company, Wugang 462500;
2. Hesteel Group Technology Research Institute, Shijiazhuang 050023;

Received:2022-08-20 Published:2023-04-01 Online:2023-03-27

摘要/Abstract

摘要： 采用扫描电镜及电子探针对55t 钢锭成材148mm 厚2.25Cr-1Mo-0.25V钢板尾部分层缺陷进行观察分析，结果表明：分层缺陷是由于模铸保护渣卷入钢液造成的。为减少钢板尾部分层缺陷，对冶炼工艺进行优化，精炼过程中采用碳粉、电石及1.2～2.0kg/tAl 线复合脱氧工艺，真空后软吹12～14 min,采用高粘度、低熔点、高熔速及膨胀系数较大的模铸保护渣。优化工艺后，钢板尾部分层缺陷出现概率分别为11.3%、9.6%、6.9%,分层缺陷导致钢板废品率由原8.1%降至1.7%。

关键词: 2.25Cr-1Mo-0.25V 钢, 148 mm厚板分层缺陷, 模铸保护渣, 浇铸, Al₂O₃夹杂物

Abstract: The delamination defects at the tail of 148 mm thickness 2.25Cr-1Mo-0.25V steel plate made of 55 t ingot is observed and analyzed by scanning electron microscope and electron probe microanalysis. The results show that the delamination defects are caused by the involvement of mold flux in the molten steel. In order to reduce the delamination defects at the tail of steel plate the smelting process is optimized,i.e. in refining process,the composite deoxidation process of carbon powder,calcium carbide and 1.2-2.0 kg/t_steel Al line is adopted. After vacuum, it is soft blown for 12-14 min. The mold casting protective slag with high viscosity,low melting point,high melting rate and large expansion coefficient is used. After optimizing the smelting process, the ratio of delamination defects at the tail of steel plate is 11.3%,9.6% and 6.9% respectively,and the scrap rate of steel plate caused by delamination defects decreases from original 8.1% to 1.7%.

Key words: 2.25Cr-1Mo-0.25V Steel, 148 mm Heavy Thickness Delamination Defect, Flux, Casting, Al₂O₃ Inclusion

侯敬超 , 赵国昌 , 庞辉勇 , 吴艳阳 , 甄光楠 , 赵燕青. 2.25Cr-1Mo-0.25V 钢148 mm 厚板尾部分层缺陷分析及控制工艺[J]. 特殊钢, 2023, 44(2): 43-47.

Hou Jingchao , Zhao Guochang , Pang Huiyong , Wu Yanyang , Zhen Guangnan , Zhao Yanqing. Analysis on Causes of Delamination Defect at 148 mm Heavy Thickness Plate Tail of 2.25Cr-1Mo-0.25V Steel and Control Process[J]. Special Steel, 2023, 44(2): 43-47.

[1]	叶明在, 邢耀进, 陈军, 林丹. 钢包耐火材料对帘线钢82A夹杂物的影响和工艺改进[J]. 特殊钢, 2022, 43(3): 60-63.
[2]	林强, 张华, 陈国威, 周琦. 压力容器钢板探伤不合格原因分析及工艺优化[J]. 特殊钢, 2017, 38(5): 17-21.
[3]	刘发友, 王国承, 孙长余, 赵昌明, 汪琦, 毛福来. 80t BOF-LF-VD-CC流程生产GCr15轴承钢控氧的工艺实践[J]. 特殊钢, 2016, 37(5): 36-36.
[4]	李胜利, 关锐, 艾新港, 许长军, 胡林. 42CrMo4钢39t锭真空浇铸和凝固过程数值模拟和生产实践[J]. 特殊钢, 2016, 37(01): 1-4.
[5]	张大江, 王翠娜, 向华, 万国喜, 郑飞. 铝镇静钢SPHC浸入式水口结瘤成因和控制工艺[J]. 特殊钢, 2015, 36(3): 30-33.
[6]	周伟基, 薄永明, 吉海峰, 潘利, 战东平. 优化脱氧工艺提高38CrMoAl钢连浇成功率[J]. 特殊钢, 2012, 33(5): 40-42.
[7]	姜周华, 李正邦. 电渣冶金技术的最新发展趋势[J]. 特殊钢, 2009, 30(6): 10-13.
[8]	尹德. 连铸板坯侧凹浇铸减少热轧钢卷侧翻宽度的工艺实践[J]. 特殊钢, 2009, 30(6): 34-35.
[9]	吴宗双, 包燕平, 刘建华, 陈刚, 龚志翔, 钟斌. 长水口氩封保护浇铸对车轮钢Φ450 mm 圆坯质量的影响[J]. 特殊钢, 2007, 28(2): 54-55.
[10]	张乔英, 王立涛, 王新华, 王万军, 李宏. 非稳态浇铸时IF钢铸坯表层夹杂物粒径的分布[J]. 特殊钢, 2006, 27(5): 9-11.
[11]	曹立国, 魏雪晴, 丁秀中, 赵宏 . 优化55 t LD-60t LF-CC 工艺提高钢的洁净度[J]. 特殊钢, 2006, 27(1): 48-50.

2.25Cr-1Mo-0.25V 钢148 mm 厚板尾部分层缺陷分析及控制工艺

Analysis on Causes of Delamination Defect at 148 mm Heavy Thickness Plate Tail of 2.25Cr-1Mo-0.25V Steel and Control Process

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

编辑推荐

Metrics

本文评价