ISSN:1003-8620

CN:42-1243/TF

主管:中信泰富特钢集团股份有限公司

主办:大冶特殊钢有限公司

特殊钢 ›› 2021, Vol. 42 ›› Issue (6): 68-71.

• 组织和性能 • 上一篇    下一篇

回火工艺对热轧U20Mn2SiCrNiMo贝氏体钢轨组织性能的影响

杨维宇1,何建中2,梁正伟2,李智丽2   

  1. 1内蒙古包钢金属制造有限责任公司研发中心,包头 014010;
    2内蒙古包钢钢联股份有限公司技术中心,包头014010
  • 收稿日期:2021-04-02 出版日期:2021-12-23 发布日期:2022-01-03
  • 通讯作者: 何健中
  • 作者简介:杨维宇(1982-),男,硕士(2009年中北大学),高级工程师, 2006年中北大学(本科)毕业,新产品开发和失效分析。
  • 基金资助:
    国家重点研发计划资助(2017YFB0304504)

Effect of Tempering Process on Microstructure and Properties  of Hot rolled U20Mn2SiCrNiMo Bainitic Rail Steel

Yang Weiyu1,He Jianzhong2,Liang Zhengwei2 , Li Zhili2   

  1. 1 Research Center of Metal Manufacture Co Ltd of Inner Mongolia Baotou Steel Union,Baotou 014010;
    2 Technical Center of Inner Mongolia Baotou Steel Union Co Ltd,Baotou 014010
  • Received:2021-04-02 Published:2021-12-23 Online:2022-01-03

摘要: U20Mn2SiCrNiMo贝氏体钢轨的生产流程为150 t 转炉-LF-VD-280 mm×380 mm铸坯轧制,终轧930~980 ℃,空冷-340 ℃ 4 h两次回火,空冷。U20Mn2SiCrNiMo钢热轧态(终轧930~980 ℃空冷)和(320 ℃一、二次回火)组织均由贝氏体、马氏体和残余奥氏体组成。力学性能试验结果表明:U20Mn2SiCrNiMo钢轨最佳回火工艺为320 ℃ 4 h空冷+320 ℃ 4 h空冷二次回火,其性能为:屈服强度1242 MPa,抗拉强度1393 MPa,HBW硬度值417,伸长率15.0%,断面收缩率60%,冲击吸收功KU2 98 J,轨底纵向残余应力+180 MPa。

Abstract: The flowsheet process of U20Mn2SiCrNiMo bainitic rail steel is 150 t BOF-LF-VD-280 mm×380 mm cast bloom-rolling,finishing at 930~980℃,air cooling -340℃ 4 h,air cooling,double tempeing.The microstructure of hotrolled(end rolling at 930~980℃ air cooling)and tempered(320 ℃once-and double-tempering)of U20Mn2SiCrNiMo steel is composed of bainite, martensite and retained austenite.Mechenical properties test results show that the optimum tempering process of U20Mn2SiCrNiMo steel rail is 320℃4 h air cooling+320℃4 hair cooling,double tempeing,its yield strength is 1242 MPa,tensile strength 1393 MPa,HBW hardness 417,elongation 15.0%,reduction of area 60%,impact absorption work Ku2 is 98 J,and longitudinal residual stress of rail bottom +180 MPa.