Thermodynamic Calculation and Experimental Research on Nitrogen Solubility in Austenite Stainless Steel

沈春飞; 蒋兴元; 李阳; 李双江; 尹世友; 姜周华

您当前的位置：

首页 >

文章列表页 >

Thermodynamic Calculation and Experimental Research on Nitrogen Solubility in Austenite Stainless Steel

更新时间：2026-01-21

- Thermodynamic Calculation and Experimental Research on Nitrogen Solubility in Austenite Stainless Steel
- Special Steel Vol. 31, Issue 5, Pages: 1-4(2010)
- 作者机构：
  
  1. 东北大学材料与冶金学院,沈阳,110004
  2. 宝钢股份有限公司不锈钢事业部,上海,200431
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：19 April 2010，
  
  Online First：10 November 2022，
  
  Published：10 November 2010
- 稿件说明：
移动端阅览
沈春飞, 蒋兴元, 李阳, et al. Thermodynamic Calculation and Experimental Research on Nitrogen Solubility in Austenite Stainless Steel[J]. Special Steel, 2010, 31(5): 1-4.
DOI：

沈春飞, 蒋兴元, 李阳, et al. Thermodynamic Calculation and Experimental Research on Nitrogen Solubility in Austenite Stainless Steel[J]. Special Steel, 2010, 31(5): 1-4. DOI：

摘要

采用热力学分析方法

对固态不锈钢304、304L、301S和301L(γ-相)以及奥氏体不锈钢熔体中氮溶解度进行了计算

得出了氮溶解度的计算模型;同时通过1 kg MoSi电阻炉对4种奥氏体不锈钢在1520～1580℃和33～100 kPa压力下的渗氮行为进行了实验研究。结果表明

氮在固态奥氏体不锈钢的γ-相中的溶解度最高;在常压冷却、凝固过程中存在的液相、δ-相至γ-相的转变;当不锈钢熔体中相对于δ-相过饱和的氮在钢中以气泡形式析出

则降低了奥氏体钢的氮含量

所以采用常压快速冷却或加压浇注有利于冶炼高氮奥氏体不锈钢。

Abstract

The solubility of nitrogen in solid stainless steel 304

304L

301S and 301L (γ-phase) and in melts of austenite stainless steel has been calculated by using thermodynamic analysis method to get computational model for solubility of nitrogen in the steels

and the experimental research on nitriding behavior in four austenite stainless steels has been carried out by 1 kg MoSi electric resistance furnace with 33-100 kPa at 1520 ~1580 ℃. Results show that the solubility of nitrogen in y- phase in solid austenite stainless steels is highest; in cooling and solidifying process at normal pressure there is a transformation process from liquid phase

δ-phase to γ-phase; the nitrogen content in austenite steel shall decrease if supersaturated nitrogen to 8- phase in melt of stainless steel precipitates as gas bubble

so it is available to melt high nitrogen austenite stainless steel by using quick cooling at normal pressure or pressurized casting.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Optimum of Mould Taper Design for Slab Casting of Austenite Stainless Steel

Processing Practice for Inclusion Controlling of Stainless Steel 0Cr18Ni9 in Refining Process of a 90 t LF

Related Author

王宝峰

丁国

赵建伟

张建国

范新智

Related Institution

内蒙古科技大学

太原钢铁公司技术中心

太钢不锈钢股份有限公司技术中心

⁰