Research on Production Technology of Asymmetrically Hot Rolled Single Sided Stainless Steel-Carbon Steel Clad Plate

陈振业; 马娥; 朱文婷; 赵燕青; 赵帅; 孙力; 王国栋

您当前的位置：

首页 >

文章列表页 >

Research on Production Technology of Asymmetrically Hot Rolled Single Sided Stainless Steel-Carbon Steel Clad Plate

更新时间：2026-01-21

- Research on Production Technology of Asymmetrically Hot Rolled Single Sided Stainless Steel-Carbon Steel Clad Plate
- Special Steel Vol. 39, Issue 6, Pages: 71-74(2018)
- 作者机构：
  
  1. 河钢集团钢研总院工艺研究所,石家庄,050000
  2. 东北大学轧制及连轧自动化国家重点实验室,沈阳,110004
  3. 燕山大学机械工程学院,秦皇岛,066004
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：19 July 2018，
  
  Online First：26 May 2022，
  
  Published：26 May 2018
- 稿件说明：
移动端阅览
陈振业, 马娥, 朱文婷, et al. Research on Production Technology of Asymmetrically Hot Rolled Single Sided Stainless Steel-Carbon Steel Clad Plate[J]. Special Steel, 2018, 39(6): 71-74.
DOI：

陈振业, 马娥, 朱文婷, et al. Research on Production Technology of Asymmetrically Hot Rolled Single Sided Stainless Steel-Carbon Steel Clad Plate[J]. Special Steel, 2018, 39(6): 71-74. DOI：

摘要

釆用“电子束真空焊接制坯+热轧”的工艺在钢厂热连轧生产线上进行了“316L不锈钢+Q345C碳钢”的单面不锈钢复合板热轧生产。采用非对称制坯及异步轧制的手段生产出了高品质单面不锈钢复合板，所生产的不锈钢复合板界面剪切强度大于320 MPa、屈服强度大于370 MPa、抗拉强度大于520 MPa、断后伸长率大于 30%

各项指标均达到GB/T8165-2008的要求。不锈钢层和碳钢层结合度良好，复合界面平直，无明显缺陷，不锈钢与碳钢之间实现了良好的冶金结合，结合率达100% 。

Abstract

The hot rolled single sided stainless steel clad plate of 316L stainless steel and Q345C carbon steel was carried out in a hot rolling line by the technology of “electron beam vacuum welding and hot rolling”. High quality single sided stainless steel clad plates were produced by asymmetrical compound billet and asymmetrically rolling. The productions of stainless steel clad plate have reached the requirements of GB/T8165-2008. The interface shear strength is greater than 320 MPa. Hie yield strength is greater than 370 MPa. The tensile strength is greater than 520 MPa. The elongation is greater than 30%

Stainless steel layer and plain carbon steel layer combining degree is good

the composite interface is straight and perfect. A good metallurgical bonding between stainless steel and carbon steel was achieved. The bonding rate reached 100%.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Finite Element Simulation for Effect of Initial Rolling Temperature on Change of Rolling Dynamic Structure of Steel 42CrMo4

Effect of Heating Process on Interface Performance of Cold Drawing-Brazing Stainless Steel/ Carbon Steel Cladding Bar

Effect of Cooling Process after Rolling on Structure and Texture of Simulated CSP Hot-Rolled Hi-B Steel Bearing Copper

Development and Performance of Hot Rolled Enamel Steel for Water Heater Tank

Research on Cracks Evolution of High Silicon Electrical Steel Fe-10 % Si and Low Carbon Steel Q235 Composite Plate in Rolling Process

Related Author

高亚男

鲍远通

张全逾

肖宏

余冲

肖欢

王艳

何晋

Related Institution

承德石油高等专科学校汽车工程系

燕山大学国家冷轧板带装备及工艺工程技术研究中心

武汉工程大学邮电与信息工程学院

武汉科技大学钢铁冶金及资源利用省部共建教育部重点实验室

山西太钢不锈钢股份有限公司技术中心

⁰