Numerical Simulation of Five-Hole Swirl Oxygen Lance for a 260 t Converter

王玺; 刘广强; 韩鹏; 冯亮花; 刘坤

您当前的位置：

首页 >

文章列表页 >

Numerical Simulation of Five-Hole Swirl Oxygen Lance for a 260 t Converter

更新时间：2026-01-21

- Numerical Simulation of Five-Hole Swirl Oxygen Lance for a 260 t Converter
- Special Steel Vol. 42, Issue 1, Pages: 21-24(2021)
- 作者机构：
  
  辽宁科技大学材料与冶金学院 2. 辽宁科技大学土木工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Online First：31 March 2022，
  
  Published：31 March 2021
- 稿件说明：
移动端阅览
王玺, 刘广强, 韩鹏, et al. Numerical Simulation of Five-Hole Swirl Oxygen Lance for a 260 t Converter[J]. Special Steel, 2021, 42(1): 21-24.
DOI：

王玺, 刘广强, 韩鹏, et al. Numerical Simulation of Five-Hole Swirl Oxygen Lance for a 260 t Converter[J]. Special Steel, 2021, 42(1): 21-24. DOI：

摘要

为克服传统氧枪在转炉炼钢工艺技术中的局限性

利用数值模拟对不同结构的五孔旋流氧枪进行模拟研究

分析了旋流氧枪的倾斜角(13°～15°)、旋流角(0～15°)对射流的衰减、聚并形态和冲击面积的影响。结果表明:与普通氧枪相比

旋流氧枪的射流速度较低

但因存在切向力

对熔池的搅拌能力更强;倾斜角增大会导致射流径向的速度分量增大;旋流氧枪由于旋流角的作用

发生射流聚并的可能性降低;倾斜角对射流的聚并有重要影响

倾斜角减小

射流聚并更加严重并且射流冲击面积会减小;当倾斜角15°并且旋流角为10°时冲击面积最大。

Abstract

In order to overcome the limitation of traditional oxygen lance in converter steelmaking technology

the five- hole swirl oxygen lance with different structure parameters is simulated study by numerical simulation. The effects of the tilt angle (13° ~15°) and swirl angle (0 - 15°) of swirl oxygen lance on jet attenuation

coalescence morphology and impact area are analyzed. The results show that the jet velocity of the swirl lance are lower than that of the ordinary lance

but the stirring capacity to the molten pool is stronger because of the tangential force； the increase of the inclination angle will increase the radial velocity component of the jet； the possibility of jet coalescence will be reduced because of the effect of the swirl angle. The tilt angle has an important effect on the jet coalescence

with the decrease of tilt angle

the coalescence of jet is more serious

and the impact area of jet decreases. When the inclination angle is 15° and the swirl angle is 10°

the impact area is largest.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Nu merical Simulation of Temperature Field of 304 Stainless Steel Rod and Wire Hot Continuous Rolling

Numeric Simulation of Three-Dimensional Flow Field of Molten Steel in a Mould with High Efficiency Inner and Outer Couple Cooling

Numerical Simulation of Fluid Field of Molten Steel in Mold for 280 mm×380 mm Billet Concasting

Physical and Mathematical Study on Flow Control Device of Tundish for 5-Strand billet Casting at Chongqing Steel

Numerical Simulation of Flow Field in Mould for Slab Continuous Casting and Optimal Operation

Related Author

廖舒纶

于永泗

张立文

原思宇

江国栋

甑玉

郭书奇

崔小朝

Related Institution

太原科技大学工程力学系

辽宁科技大学材料学院

鞍山钢铁集团技术中心

重庆大学材料科学与工程学院

重庆钢铁集团有限公司

⁰