Smelting Process Practice to Improve the Cleanliness and Polishling Proptice of Die Steel

LiuYong; Zhang Yunfei; Zhao YingLi; Zhao Nan; Zhao Zhengrong; Fan Mingqiang; Tian Zhiqiang

doi:10.20057/j.1003-8620.2024-00034

您当前的位置：

首页 >

文章列表页 >

Smelting Process Practice to Improve the Cleanliness and Polishling Proptice of Die Steel

Product Research and Development | 更新时间：2025-05-09

- Smelting Process Practice to Improve the Cleanliness and Polishling Proptice of Die Steel
- Special Steel Vol. 45, Issue 5, Pages: 47-52(2024)
- 作者机构：
  
  河钢材料技术研究院特种材料研发中心，石家庄 052165
- 作者简介：
- 基金信息：
- DOI：10.20057/j.1003-8620.2024-00034
  CLC： TF769.2;TF769.4
- Received：19 February 2024，
  
  Published：30 September 2024
- 稿件说明：
移动端阅览
刘泳,张雲飞,赵英利等.改善模具钢洁净度与抛光性能的冶炼工艺实践[J].特殊钢,2024,45(05):47-52.

LiuYong ,Zhang Yunfei,Zhao YingLi,et al.Smelting Process Practice to Improve the Cleanliness and Polishling Proptice of Die Steel[J].Special Steel,2024,45(05):47-52.
刘泳,张雲飞,赵英利等.改善模具钢洁净度与抛光性能的冶炼工艺实践[J].特殊钢,2024,45(05):47-52. DOI： 10.20057/j.1003-8620.2024-00034.

LiuYong ,Zhang Yunfei,Zhao YingLi,et al.Smelting Process Practice to Improve the Cleanliness and Polishling Proptice of Die Steel[J].Special Steel,2024,45(05):47-52. DOI： 10.20057/j.1003-8620.2024-00034.

摘要

为解决模具钢H13镜面抛光效应较差的问题，通过冶炼工艺优化改进，改善模具钢的抛光效应。研究结果表明，镜面效应与钢的洁净度有密切对应关系。从电弧炉配料结构、脱氧制度、LF精炼炉吹氩控制、VD真空炉的高真空度周期优化，较全面地采取了改进措施，即电弧炉配料时采用增加DRI的使用量，采用硅预脱氧，优化钢包底吹氩控制和提高VD高真空度周期等措施。夹杂物有效尺寸从优化前的27.93 μm下降到23.65 μm，夹杂物数密度从256个/cm

，下降到176个/cm

，夹杂物数密度下降了31.2%，B类和DS类以及TiN类夹杂物总量上得到了控制，抛光性能的顾客满意度得到了一定的认可。

Abstract

In order to solve the problem of poor mirror polishing effect of steel used in plastic die， the polishing efficiency of die steel is improved by optimizing smelting process. The results showed that the mirror effect

was closely related to the purity of steel. From the electric arc furnace burden structure， deoxidization system， LF refining furnace argon blowing control， high vacuum degree cycle of VD vacuum furnace and mold casting process optimization， more comprehensive improvement measures were taken， that is， increasing the use of DRI， using silicon predeoxygenation， optimizing the argon blowing control of steel ladle bottom and improving the high vacuum cycle of VD.The effective size of inclusions decreased from 27.93 μm to 23.65 μm before optimization. The number density of inclusions decreased from 256 / cm

to 176 / cm

， and the number density of inclusions decreased by 31.2%. The total amount of B and DS and TiN inclusions was controlled， and the customer satisfaction of polishing performance was recognized.

关键词

Keywords

references

曹锡梅 . 我国模具钢抛光标准的思考［J］. 模具制造， 2018 ， 18 （ 8 ）： 68 - 70 .

李维华 . 电炉连铸坯中氮含量控制技术研究［J］. 福建冶金， 2023 ， 52 （ 2 ）： 35 - 38 .

袁金甲 . 电炉炼钢原料及直接还原铁生产技术［J］. 冶金与材料， 2022 ， 42 （ 2 ）： 101 - 102 .

贺美乐，张豫川，王　庆，等 . 电弧炉采用直接还原铁炼钢工艺技术分析［J］. 特殊钢， 2023 ， 44 （ 5 ）： 33 - 38 .

陈军召等 . 喷吹微粒脱磷法在130 t 电弧炉炼钢中的应用［J］. 特殊钢， 2023 ， 44 （ 2 ）： 34 - 38 .

凌天鹰，徐匡迪，蒋国昌 . 氮在Ca-SiO 2 -Al 2 O 3 渣中的热力学研究［J］. 钢铁研究学报， 1990 ， 2 （ 1 ）： 13 - 19 .

刘同威，张燕超，张彩军，等 . 吹氩条件下结晶器钢渣液面波动行为［J］. 连铸， 2022 ， 47 （ 3 ）： 18 - 24 .

邓南阳，孙　波，解养国，等 . 120 t LF精炼过程钢水吸氮量控制［J］. 炼钢， 2023 ， 39 （ 3 ）： 44 - 51 .

周世祥，傅　杰，王　平 . EAF-LF-VD-WF-CC工艺生产低氮钢技术［J］. 特殊钢， 1998 ， 19 （ 1 ）： 1 - 6 .

E . A . Vieira等使用合成精炼渣控制钢中夹杂含量.《2019年全国高效连铸应用技术及铸坯质量控制研讨会论文集》， 2019 ： 407 - 413 .

贾　毅，刘春阳，韩少伟，等 . 铝镇静钢氮含量控制分析［J］. 中国冶金， 2021 ， 31 （ 3 ）： 116 - 121 .

周同军，刘军占 . 模铸氩气保护浇注的工艺实践［J］. 世界钢铁， 2012 ， 12 （ 5 ）： 34 - 37 .

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of Nitrogen Content and Final Rolling Temperature on Low-temperature Impact Toughness of Titanium Microalloyed High-strength Steel CGLC700

Effect of Different Residual Steel Amounts on Molten Steel Cleanliness

Technology for Controlling Nitrogen Content in Molten Steel Melted by 120-ton Top-bottom Reblowing Converter

Development of Continuous Casting Round Billet for P92 Heat-resistant Steel for Ultra-supercritical Boiler Tubes

Research on the Metallurgical Properties of Fluorine-Containing Refining Slag and Its Fluoride-Free Design

Related Author

Chen Yufeng

Zhang Junfen

Xue Qihe

Bai Jun

Yang Shufeng

Li Jingshe

Ren Ying

Liu Zhonghua

Related Institution

Chengde Branch， HBIS Group Co.， Ltd.

School of Metallurgical and Ecological Engineering，University of Science and Technology Beijing

School of Mechanical and Materials Engineering， North China University of Technology

Metallurgical Corporation of China （MCC） CADI Ironmaking Division

Tangshan Iron and Steel Group Co.， Ltd.， Research and Development Center

⁰