Study on Hot Deformation Processing Map of Super Martensitic Stainless Steel SUP13 Cr5Ni2Mo for Oil-Gas Field

Special Steel ›› 2018, Vol. 39 ›› Issue (5): 1-4.

Special Issue: 马氏体不锈钢

Study on Hot Deformation Processing Map of Super Martensitic Stainless Steel SUP13 Cr5Ni2Mo for Oil-Gas Field

Fang Xudong^1,2, Wang Yan^1,2, Xia Yan^1,2 ,Li Sha^1,2 ， Li Yang^1,2

1 State Key Laboratory of Advanced Stainless Steel, Taiyuan Iron and Steel Group Company Limited, Taiyuan 030003 ；
2 Technology Center, Shanxi Taigang Stainless Steel Co. , Ltd, Taiyuan 030003

Received:2018-04-10 Online:2018-10-01 Published:2022-05-27

油气田用SUP13Cr5Ni2Mo超级马氏体不锈钢热变形加工图研究

方旭东^1,2，王岩^1,2，夏炎^1,2，李莎^1,2，李阳^1,2

1太原钢铁(集团)有限公司先进不锈钢材料国家重点实验室，太原030003 ；
2山西太钢不锈钢股份有限公司技术中心，太原030003

作者简介:方旭东(1975-)，男，硕士(2014年太原理工大学),高级工程师,1997年天津理工学院(本科)毕业，不锈钢型材和无缝管研发。
基金资助:
国家重点研发计划课题(2016YFB0300204)资助

Abstract

Abstract: The thermo plastic and thermo deformation characteristics of SUP13Cr5Ni2Mo alloy were studied by using Gleeble-3800 thermal simulation test machine, and the hot processing maps were established. The results show that： In the range of 900 ~ 1 300°C, the alloys have good thermoplastic ；The suitable processing of initial in a temperature range between 1 100 ~ 1 200 °C through hot processing map analysis, and the deformation microstructure sample is fine and uniform by using this parameters.

摘要： 在Gleeble-3800热模拟试验机上,研究了SUP13Cr5Ni2Mo合金的热塑性及热变形行为,并建立了合金的热加工图。结果表明,在900～1 300℃,合金均具有较好的热塑性;通过热加工图分析得出,合金适宜初始加工温度范围在1 100～1 200℃,采用此参数变形获得的组织细小均匀。

Fang Xudong, Wang Yan, Xia Yan, , Li Sha, Li Yang. Study on Hot Deformation Processing Map of Super Martensitic Stainless Steel SUP13 Cr5Ni2Mo for Oil-Gas Field[J]. Special Steel, 2018, 39(5): 1-4.

方旭东, 王岩, 夏炎, 李莎, 李阳, . 油气田用SUP13Cr5Ni2Mo超级马氏体不锈钢热变形加工图研究[J]. 特殊钢, 2018, 39(5): 1-4.

References

[1]Rae C. Alloys by Design: Modelling Next Generation Superalloys [J]. Materials Science and Technology,2009,25(4) : 479-487.
[2]Cowen C J,Danielson P E and Jablonski P D. TTie Microstructural Evolution of Inconel Alloy 740 During Solution Treatment, Aging, and Exposure at 760 T； [J]. Journal of Materials Engineering and Performance,2011,20(6) ： 1078-1083.
[3]Viswanathan R,Coleman K and Rao U. Materials for Ultra-Supercritical Coal-Fired Power Paint Boilers [J].International Journal of Pressure Vessels and Piping ,2006,83(11 -12 ) :778-783.
[4]谢锡善，赵双群,董建新，等.超超临界电站用Inconel740镍基合金的组织稳定性及其改型研究[J].动力工程学报,2011,31(8):638-643.
[5]赵美兰，孙文儒,杨树林，等.GH761变形高温合金的热变形行为[J].金属学报,2009,45(1) ：793-83
[6]Mcqueen H J. Development of Dynamic Recrystallization Theory [J]. Materials Science and Engineering (A) , 2004, ( 387-389 ): 203-208.
[7] Poliakt E I and Jonass J J. A One-Parameter Approach to Determining the Critical Condition for the Initiation of Dynamic Recrystallization [J]. Acta Materialia, 1996,44(1).127-136.
[8]李莎，曾莉,苗华军，等.镍基高温合金GH4700的热变形行为及热加工图[J]，材料热处理学报,2013,34(9) ：51-56,
[9]Mcqueen H J and Ryan N D. Constitutive Analysis in Hot Working [J]. Materials Science and Engineering(A) ,2002,322；43-63.
[10]Robi P S and Dixit U S. Application of Neural Networks in Generating Processing Map for Hot Working] J]. Journal of Materials Processing Technology ,2003, 142 : 289-294.
[11]王岩，方旭东,范光伟，等.超超临界锅炉用S31042钢的热变形加工图[J].金属热处理,2015,40(4):35-38.
[12]Paik N K,Yoem J T and Na Y S. Characterization of Deformation Stability in Hot Foiling of Conventional Ti-6A1-4V Using Processing Maps[J]. Journal of Materials Processing Technology,2002, 130-131(3)：540-545.

Study on Hot Deformation Processing Map of Super Martensitic Stainless Steel SUP13 Cr5Ni2Mo for Oil-Gas Field

油气田用SUP13Cr5Ni2Mo超级马氏体不锈钢热变形加工图研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 0

Recommended Articles

Metrics

Comments