Numerical Simulation of a New Type Submerged Entry Nozzle for 200 mm x 200 mm Billet Continuous Casting

Special Steel ›› 2014, Vol. 35 ›› Issue (2): 13-15.

Previous Articles Next Articles

Numerical Simulation of a New Type Submerged Entry Nozzle for 200 mm x 200 mm Billet Continuous Casting

Chen Yuanqing^1,2 , Shang Zhenghong¹ , Tao Naibiao¹ , Wang Jin¹ , Qiu Shengtao²

1. Zhangjiagang Lianfeng Iron & Steel Research Institute Co Ltd, Zhangjiagang 215628；
2. National Engineering and Research Center for Continuous Casting Technology, Central Iron and Steel Research Institute, Beijing 100081;

Received:2013-10-15 Online:2014-04-01 Published:2022-09-07

200 mm x200 mm方坯连铸用新型浸入式水口的数值模拟

陈远清^1,2，尚正鸿¹，陶乃标¹，王进¹，仇圣桃²

1.张家港联峰钢铁研究所有限公司,张家港215628；
2.钢铁研究总院连铸技术国家工程研究中心，北京100081 ;

作者简介:陈远清(1981-)，男，硕士，博士研究生(钢铁研究总院)，工程师,2004年重庆大学(本科)毕业，炼钢及连铸工艺研究。

Abstract

Abstract: In order to alleviate the impact of flow jet of nozzle side-ports on solidifying shell and easy to use the sideport nozzle to the mold for casting square billet with smaller cross section, a design idea of submerged entry nozzle ( SEN) with flabelliform side-ports is advanced. The characteristics of flow field and temperature field in mold for casting 200 mm x 200 mm billet with straight channel nozzle, rectangular side-ports nozzle and flabelliform side-ports nozzle are analyzed and compared by using three dimension math model of fluid flow and heat transfer in mold. Research results show that the side-ports nozzle is available to reduce the impact depth of flow jet, improve the inclusions floating up, and increase the temperature and activity of liquid at meniscus and favorable to smelt slag; the flow from flabelliform side-port is more disperse, so the effect of impact on solidifying shell is sharply decreasing.

Key words: Square Billet, Submerged Entry Nozzle, Flabelliform Side-Port, Flow Field, Temperature Field, Numerical Simulation

摘要： 为了减轻水口侧孔射流对凝固坯壳的冲刷,便于侧孔水口在较小断面的方坯连铸上使用,提出扇形侧孔的水口设计理念。利用结晶器内钢水流动、传热的三维数学模型,分析比较了直筒形水口、矩形侧孔水口和扇形侧孔水口条件下200 mm×200 mm的方坯结晶器内的流场及温度场特征。研究结果表明,侧孔水口能降低射流冲击深度,促进夹杂物上浮,并提高弯月面温度和活跃程度,有利于化渣;扇形侧孔射流较分散,对凝固坯壳的冲刷作用显著减弱。

关键词: 方坯, 浸入式水口, 扇形侧孔, 流场, 温度场, 数值模拟

Chen Yuanqing , Shang Zhenghong , Tao Naibiao , Wang Jin , Qiu Shengtao. Numerical Simulation of a New Type Submerged Entry Nozzle for 200 mm x 200 mm Billet Continuous Casting[J]. Special Steel, 2014, 35(2): 13-15.

陈远清, 尚正鸿, 陶乃标, 王进, 仇圣桃. 200 mm x200 mm方坯连铸用新型浸入式水口的数值模拟[J]. 特殊钢, 2014, 35(2): 13-15.

[1]	Fu　Chengzhe, Zhang　Shuai, Wang　Shuang, Gao　Hong, Wang　Fuyue, Zhang　Zherui. Thermodynamic Coupling Analysis of Air Cooling for X70 Pipeline Steel Continuous Casting Slab Based on ABAQUS [J]. Special Steel, 2024, 45(6): 62-68.
[2]	Li Qi, Qiu Guoxing, Wang Gongliang, Gao Peng, Li Rongxiang. Numerical Simulation of Bottom Argon Blowing Process for 130 Ton Ladle [J]. Special Steel, 2024, 45(5): 59-65.
[3]	Sun Jiayi, Dong Longpei, ZHao Yunshon, Wang Enhui, Hou Xinmei. Research Progress on Numerical Simulation of Temperature Field during Directional Solidification of Nickel-based Single Crystal Turbine Blades [J]. Special Steel, 2024, 45(4): 34-40.
[4]	Mei　Feiqiang, Zhao　Jiqing, Yan　Lei, Wang　Yunhai, Yang　Gang. Simulation and Test Validation on Die forging Process of 1Cr16Co5Ni2MoWVNbN Heat-resistant Steel Ball seat [J]. Special Steel, 2024, 45(4): 131-138.
[5]	Zhou　Yang, Zhu　Hongchun, Li　Huabing, Jiang　Zhouhua, He　Zhiyu, Ni　Zhuowen. Simulation of Columnar Crystal Growth in Forced Flow of VAR Based on Phase Field Method [J]. Special Steel, 2024, 45(4): 41-46.
[6]	Zhao　Peng, Gui　Kaixuan, Qu　Jinglong, Yang　Shufeng. Numerical Simulation and Industrial Experiment of Vacuum Arc Remelting ϕ690 mm Large-sized GH4738 Superalloy Ingot [J]. Special Steel, 2024, 45(4): 55-60.
[7]	Wang Guotao, Wang Guiquan, Liu Zhongli, Wang Mingjia. Forming Process and Analysis of 436L Ferritic Stainless Steel Heat Exchanger Plate [J]. Special Steel, 2024, 45(3): 62-69.
[8]	Yang　Fengguo, Wang　Xiaoying, Zhou　Mingxing, Zheng　Bing, Xu　Dong. Effect of Different Argon Blowing Modes on Refining Effect of Molten Steel [J]. Special Steel, 2024, 45(1): 54-60.
[9]	Li　Jingshe, Wang　Cun, Chen　Yongfeng, Yang　Shufeng, Liu　Wei, Bai　Yun, Huang　Chengyong, Sun　Ye. Research and Application Progress of Plasma Heating Technology for Continuous Casting Tundish [J]. Special Steel, 2024, 45(1): 1-11.
[10]	Xu　Letian, Liu　Liangyong, Li　Yunlong, Xu　Yaowen, Wan　Wuxia. Simulation Trial and Finite Element Simulation Study on Temperature Field of Pipes in Walking Beam Reheating Furnace [J]. Special Steel, 2023, 44(6): 89-95.
[11]	Liu　Qilong, Deng　Yong, Li　Huagang, Wei　Rujun, Cao　Chenghu, Zhang　Min. Numerical simulation and Process Practice of Mold Electromagnetic Stirring for IF Steel Slab [J]. Special Steel, 2023, 44(6): 83-88.
[12]	Zeng　Zhaopeng, Du　Xiqian, Wang　Yao, Ma　Jianchao. Optimization and Simulation of Stirring Process for 100 t Electric Arc Furnace Bath and Its Application [J]. Special Steel, 2023, 44(6): 45-52.
[13]	Wang　Xiaohui, Zhang　Xueling, Wang　Lin, Liu　Zhenbao, Liang　Jianxiong, Yang　Zhiyong, Tian　Shuai, Wang　Changjun , Sun　Yongqing. Investigation of Composition Uniformity Control of Low Cost Corrosion Resistant High Strength Stainless Steel [J]. Special Steel, 2023, 44(5): 69-75.
[14]	Yang　Dongya, Peng　Qichun, Tong　Zhibo, Liu　Hongjun, Wu　Pinghui, Tan　Dajin, Xie　Cheng. Optimization and Industrial Application of 210 t Converter Oxygen Lance Jet-Flow Performance [J]. Special Steel, 2023, 44(4): 15-21.
[15]	Han　Dong. Optimization Design and Production Practice for Increasing Rolling Yield of Die Steel 3.1 t Ingot [J]. Special Steel, 2023, 44(3): 14-19.

Numerical Simulation of a New Type Submerged Entry Nozzle for 200 mm x 200 mm Billet Continuous Casting

200 mm x200 mm方坯连铸用新型浸入式水口的数值模拟

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments