Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15

廖舒纶; 张立文; 岳重祥; 高惠菊; 郭书奇

您当前的位置：

首页 >

文章列表页 >

Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15

更新时间：2026-01-21

- Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15
- Special Steel Vol. 28, Issue 5, Pages: 31-33(2007)
- 作者机构：
  
  1. 大连理工大学材料科学与工程学院,大连,116023
  2. 东北特钢集团棒线材连轧厂,大连,116031
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：18 April 2007，
  
  Online First：13 February 2023，
  
  Published：13 February 2007
- 稿件说明：
移动端阅览
廖舒纶, 张立文, 岳重祥, et al. Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15[J]. Special Steel, 2007, 28(5): 31-33.
DOI：

廖舒纶, 张立文, 岳重祥, et al. Two-and Three-Dimensional Simulation of Continuous Rolling Process for Rod of Bearing Steel GCr15[J]. Special Steel, 2007, 28(5): 31-33. DOI：

摘要

借助商业有限元软件MSC.Marc建立了GCr15轴承钢150 mm×150 mm坯至φ32 mm棒材的12道次连轧过程的二维和三维模型

并对比了二维和三维模型对轧制过程轧件截面形状、温度的模拟结果。结果表明

与三维模型相比

二维模型模拟得到的轧件截面宽展偏大

但计算效率较高

得出的温度曲线接近三维模型的模拟结果;给定工艺参数的三维模拟较二维模拟准确;模型模拟得到的出口轧制速度和温度与实测值吻合。

Abstract

The two- and three-dimensional models of 12 pass continuous rolling process for 150 mm × 150 mm billet to φ32 mm rod have been established by commercial finite element software MSC .Marc

and the simulation results of cross section shape

temperature of rolling stock during rolling process by two- and three-dimensional models were compared. Results showed that as compared with that calculated by three dimensional model

the width spread of cross section calculated by two-dimensional model is larger but by which the computational efficiency is high and the temperature curves were close to that calculated by three dimensional model; the three dimensional simulation on given process parameter was more accurate than two dimensional simulation; the simulated value of exit rolling speed and temperature obtained by simulation agreed with experimental value.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influence of Rolling Deformation on Interlamellar Spacing of Pearlite in U75V Heavy Rail Steel

Effect of Multi-Stand Pipe Mill Rolling and Sizing Process on Structure and Property of N80 Non-Quenching and Tempering Steel 36-40Mn2V for Oil Well Pipe

Related Author

王晓丽

宋波

焦国利

方剑

李阳华

邹喜洋

谢凯意

周勇

Related Institution

北京科技大学冶金与生态工程学院

包头钢铁职业技术学院

包头钢铁公司机制公司

武汉科技大学钢铁冶金及资源利用省部共建教育部重点实验室

衡阳华菱钢管(集团)有限公司

⁰