Finite Element Analysis on Temperature Field of Finishing Rolled 20CrMnTiH Steel Round Bar during Controlled Cooling

程满; 洪慧平; 王莉; 康永林; 金永春

您当前的位置：

首页 >

文章列表页 >

Finite Element Analysis on Temperature Field of Finishing Rolled 20CrMnTiH Steel Round Bar during Controlled Cooling

更新时间：2026-01-21

- Finite Element Analysis on Temperature Field of Finishing Rolled 20CrMnTiH Steel Round Bar during Controlled Cooling
- Special Steel Vol. 28, Issue 3, Pages: 1-3(2007)
- 作者机构：
  
  1. 北京科技大学材料科学与工程学院,北京,100083
  2. 中钢设备公司,北京,100080
  3. 首钢技术研究院,北京,100041
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：08 December 2006，
  
  Online First：30 January 2023，
  
  Published：30 January 2007
- 稿件说明：
移动端阅览
程满, 洪慧平, 王莉, et al. Finite Element Analysis on Temperature Field of Finishing Rolled 20CrMnTiH Steel Round Bar during Controlled Cooling[J]. Special Steel, 2007, 28(3): 1-3.
DOI：

程满, 洪慧平, 王莉, et al. Finite Element Analysis on Temperature Field of Finishing Rolled 20CrMnTiH Steel Round Bar during Controlled Cooling[J]. Special Steel, 2007, 28(3): 1-3. DOI：

摘要

通过对20CrMnTiH圆钢精轧后控制冷却过程温度场进行有限元模拟以及现场温度实测

得出了Φ35 mm规格圆钢芯部、1/2半径处和表层温度的分布曲线。分析说明

轧后水冷却过程圆钢表层温度急速下降

而芯部温度下降缓慢

水冷时圆钢芯部与表面的最大温差约为115℃;水冷后的空冷过程使得圆钢芯部和表层温度逐渐一致。20CrMnTiH圆钢精轧后采用快速水冷并配合空冷工艺

有利于抑制奥氏体晶粒长大并获得均匀细小的轧材组织。

Abstract

The temperature distribution curves at core

1/2 radius and surface of the Φ35 mm round bar of 20CrMnTiH steel have been got by finite element simulating and situ temperature measuring to finishing rolled round steel bar during controlled cooling. Analysis results indicated that the temperature at surface of finished rolled round bar quickly dropped during water cooling while the temperature at core of steel decreased slowly ； the maximum temperature difference between the surface and the core of round bar was about 115 ℃ during water cooling ； and after water cooling the temperature of surface and core of round steel tended towards equality during air cooling. To adopt quick water cooling and combined air cooling process is available to inhibit austenite grain growth and obtain fine and dispersed structure of finished rolled 20CrMnTiH round steel products.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Finite Element Simulation of Stable State Temperature Field of Ladle

A Numerical Simulation Analysis on Safety of Mould for 165 mm×165 mm Billet Concasting

Calculation Model and Evolution Law of Temperature Field and Phase Precipitation along the Entire Line of Cold Heading Steel SCM435 High-Speed Wire Rod

Thermodynamic Coupling Analysis of Air Cooling for X70 Pipeline Steel Continuous Casting Slab Based on ABAQUS

Simulation of Columnar Crystal Growth in Forced Flow of VAR Based on Phase Field Method

Related Author

杨治立

朱光俊

常长志

陈艳霞

周雄

Gu Zuohong

Zhou Min

Tan Guangyao

Related Institution

重庆科技学院冶金与材料工程学院

湘潭大学研究生学院

太原科技大学工程力学系

Institute of Metal Materials， CISDI Research and Development Co.， Ltd.

Casting and Rolling Division，CISDI Shanghai Engineering Co.， Ltd.

⁰