Effect of Ageing Treatment and Nitrogen Content on Impact Toughness of Ultra-Low Carbon Austenite Stainless Steel 316L

张剑桥; 刘承志

您当前的位置：

首页 >

文章列表页 >

Effect of Ageing Treatment and Nitrogen Content on Impact Toughness of Ultra-Low Carbon Austenite Stainless Steel 316L

更新时间：2026-01-21

- Effect of Ageing Treatment and Nitrogen Content on Impact Toughness of Ultra-Low Carbon Austenite Stainless Steel 316L
- Special Steel Vol. 32, Issue 6, Pages: 60-61(2011)
- 作者机构：
  
  山西太钢不锈钢股份有限公司技术中心,太原,030003
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：29 June 2011，
  
  Online First：19 October 2022，
  
  Published：19 October 2011
- 稿件说明：
移动端阅览
张剑桥, 刘承志. Effect of Ageing Treatment and Nitrogen Content on Impact Toughness of Ultra-Low Carbon Austenite Stainless Steel 316L[J]. Special Steel, 2011, 32(6): 60-61.
DOI：

张剑桥, 刘承志. Effect of Ageing Treatment and Nitrogen Content on Impact Toughness of Ultra-Low Carbon Austenite Stainless Steel 316L[J]. Special Steel, 2011, 32(6): 60-61. DOI：

摘要

316L超低碳不锈钢(/%:0.010～0.013C、17.50～17.67Cr、10.10～10.60Ni、1.89～2.02Mo、0.020～0.201N)由200 kg真空感应炉冶炼

并经550 mm轧机热轧成15 mm钢板。研究了1 050℃40 min水冷

750℃25～100 h空冷后316L钢的组织和冲击韧性。结果表明

随时效时间增加

316L钢的冲击功下降;同样时效时间

0.201%N的高氮316L钢的冲击功低于0.020%N较低氮316L钢

750℃100 h时效后两者的冲击功分别为40 J和150 J。低氮316L钢主要析出物为碳化物

在晶界和晶内呈细小弥散分布

尺寸为3～5μm;高氮316L钢析出物为100～200μm氮碳化物和σ-相

沿晶界分布。

Abstract

The test ultra-low carbon austenite stainless steel 316L (/%: 0. 010 〜0. 013C

17. 50 〜17. 67Cr

10. 10-10. 60Ni

1.89 〜2. 02Mo

0. 020 - 0. 201 N) is melted by a 200 kg vacuum induction furnace and hot rolled to 15 mm steel plate by 550 mm mill. The structure and impact toughness of steel 316L heat treated at 1 050 T for 40 min

water cooling

then at 750℃ for 25 ~ 100 h

air cooling has been studied. Results show that with increasing ageing time the impact energy of steel 316L decreases ； with same ageing time the impact energy of 0. 201% N high nitrogen steel 316L is lower than that of 0. 020% N low nitrogen steel 316L

with ageing at 750 ℃ for 100 h

the impact energies of high and low nitrogen steel 316L are respectively 40 J and 150 J ； the main precipitates in low nitrogen steel 316L are 3 ~5 μm carbides dispersed distributed at grain boundary and in grain and the main precipitates in high nitrogen steel 316L are 100 〜200 μm carbo-nitride and σ- phase distributed along grain boundary.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰