Effect of Recycling Phase Transformation on Grain Refinement and Mechanical Properties of Maraging Stainless Steel 00Cr13Ni7Co5Mo4Ti

姜越; 周蓓蓓; 艾莹莹; 卢伟

您当前的位置：

首页 >

文章列表页 >

Effect of Recycling Phase Transformation on Grain Refinement and Mechanical Properties of Maraging Stainless Steel 00Cr13Ni7Co5Mo4Ti

更新时间：2026-01-21

- Effect of Recycling Phase Transformation on Grain Refinement and Mechanical Properties of Maraging Stainless Steel 00Cr13Ni7Co5Mo4Ti
- Special Steel Vol. 33, Issue 3, Pages: 41-43(2012)
- 作者机构：
  
  哈尔滨理工大学应用科学学院,哈尔滨,150080
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：11 November 2011，
  
  Online First：13 October 2022，
  
  Published：13 October 2012
- 稿件说明：
移动端阅览
姜越, 周蓓蓓, 艾莹莹, et al. Effect of Recycling Phase Transformation on Grain Refinement and Mechanical Properties of Maraging Stainless Steel 00Cr13Ni7Co5Mo4Ti[J]. Special Steel, 2012, 33(3): 41-43.
DOI：

姜越, 周蓓蓓, 艾莹莹, et al. Effect of Recycling Phase Transformation on Grain Refinement and Mechanical Properties of Maraging Stainless Steel 00Cr13Ni7Co5Mo4Ti[J]. Special Steel, 2012, 33(3): 41-43. DOI：

摘要

研究了00Cr13Ni7Co5Mo4Ti马氏体时效不锈钢(/%:0.009C、13.28Cr、7.37Ni、5.36Co、3.59Mo、0.66Ti)经4次860℃15 min水冷循环处理的细化晶粒工艺对力学性能的影响。以1 100℃1 h固溶处理的组织为原始组织

经3～4次循环相变处理后

马氏体时效不锈钢的晶粒尺寸由180μm细化至10μm的细小等轴晶粒。与传统1 100℃1 h固溶+450℃9 h时效工艺相比

经1 100℃1 h固溶+860℃15 min水冷α′↔γ循环相变+450℃9 h时效的钢的屈服强度σ

0.2

由1 420 MPa提高至1 560 MPa

伸长率δ由12.6%提高至14.9%。

Abstract

The effect of grain refining process with 4 times 860 Y 15 min water cooling recycling treatment on mechanical properties of maraging stainless steel 00Crl3Ni7Co5Mo4Ti (/% ： 0. 009C

13. 28Cr

7. 37Ni

5. 36Co

3. 59Mo

0. 66Ti) has been studied. Based on the original structure of steel with 1 100 ℃ 1 h solid solution treatment

after 3 ~4 times recycling phase transformation treatment

the grain size of maraging steel refines to 10 μm equiaxed fine grains from original 180 μm. Compared with traditional 1 100 ℃ 1 h solid solution +450 ℃ 9 h aging process

with 1 100℃1 h solid solution +860 °C 15 min water cooling α′↔γ phase transformation +450 ℃ 9 h aging

the yield σ

0.2

of steel increases to 1 560 MPa from 1 420 MPa and the elongation δ increases to 14. 9% from 12. 6%.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influence of Phosphorus Microalloying on Molidification， Hot Deformation and Mechanical Properties in Nickel/Nickel Iron-based Alloys

Effect of Heat Treatment on Mechanical Properties of High Strength Free-Cutting Precipitation Hardening Stainless Steel 2Cr16Ni3Mo2CuN

Effect of Quenching and Tempering Process on Mechanical Properties of Spring Steel 60Si2CrVAT

Structure and Mechanical Properties of Linepipe Steel X80

Production Practice of Steel 37CrMnMo for Coupling Sleeve of Petroleum Drill Stem

Related Author

Wu Yunsheng

Wu Hao

Zhao Yong

Pei Yubing

Wang Tianjian

Jiang Lei

Xu Ziyu

Gao Zhenhuan

Related Institution

State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment

Dongfang Turbine Co.，Ltd.， Dongfang Electric Corporation

changxu Innovation Center for Advanced Materials， Institute of Metal Research， Chinese Academy of Sciences

江阴兴澄特种钢铁有限公司，江阴

中国石油天然气集团公司管材研究所

⁰