Finite Element Numerical-Simulation and Analysis on BD2 Blooming Process of Heavy Rail Steel U75V

陈林; 孙盛志

您当前的位置：

首页 >

文章列表页 >

Finite Element Numerical-Simulation and Analysis on BD2 Blooming Process of Heavy Rail Steel U75V

更新时间：2026-01-21

- Finite Element Numerical-Simulation and Analysis on BD2 Blooming Process of Heavy Rail Steel U75V
- Special Steel Vol. 33, Issue 3, Pages: 12-14(2012)
- 作者机构：
  
  内蒙古科技大学材料与冶金学院,包头,014010
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：13 November 2011，
  
  Online First：13 October 2022，
  
  Published：13 October 2012
- 稿件说明：
移动端阅览
陈林, 孙盛志. Finite Element Numerical-Simulation and Analysis on BD2 Blooming Process of Heavy Rail Steel U75V[J]. Special Steel, 2012, 33(3): 12-14.
DOI：

陈林, 孙盛志. Finite Element Numerical-Simulation and Analysis on BD2 Blooming Process of Heavy Rail Steel U75V[J]. Special Steel, 2012, 33(3): 12-14. DOI：

摘要

通过ANSYS/LS-DYNA非线性有限元软件对重轨钢U75V(/%:0.70～0.78C、0.50～0.70Si、0.75～1.05Mn、≤0.025P、0.008～0.025S、0.04～0.08V)在BD2轧机于1 200℃开坯5道次轧制过程进行了数值模拟

分析了各道次稳定断面处等效应力、等效应变的分布情况。结果表明

轧件头部、腰部和底部随每道次的变化其应力、应变分布存在差异;稳定截面处轨头、轨腰和轨底各道次应力曲线的分析得出

轨头应力变化最大

最大值达64.8 MPa

提高重轨轨头的屈服强度有利于延长重轨寿命。

Abstract

The numerical-simulation on blooming and rolling process with 5 passes of BD2 mill at 1 200 °C for heavy rail steel U75V (/% : 0. 70 〜0. 78C

0.50 〜0. 70Si

0. 75 ~1.05Mn

≤0.025P

0. 008 〜0. 025S

0. 04 〜0. 08V) has been carried out by using nonlinear finite element software ANSYS/LS-DY

and the distribution of equivalent stress and equivalent strain at stable-section of rolling piece in each pass is analyzed. Results show that with change of each pass the distribution of stress and strain in head

waist and bottom of rolling piece is deferent ； it is obtained by analysis on rail head

waist and bottom at stable-section of rolling piece that the change of stress in head is largest

its maximum value is up to 64. 8 MPa

so increasing the yield strength of head of heavy rail is available to prolong the life of heavy rail.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Simulation Calculation on 250 ~ 320 mm Casting Slab during Stacking Slow Cooling Process

Numerical Simulation and Process Improvement on Rough Rolling of 250 mm x 280 mm Cast Bloom to 138 mm x 150 nun Billet of GCr15 Bearing Steel

Nu merical Simulation of Temperature Field of 304 Stainless Steel Rod and Wire Hot Continuous Rolling

Numeric Simulation of Three-Dimensional Flow Field of Molten Steel in a Mould with High Efficiency Inner and Outer Couple Cooling

Numerical Simulation of Fluid Field of Molten Steel in Mold for 280 mm×380 mm Billet Concasting

Related Author

王卫华

王文军

刘洋

陈霞

苟复钢

王青海

王东明

孙世平

Related Institution

首钢技术研究院

西宁特殊钢集团有限责任公司1精品小棒线分厂，2股份公司

太原科技大学工程力学系

辽宁科技大学材料学院

鞍山钢铁集团技术中心

⁰