Effect of Electro-Slag Remelting on Chemical Composition and Characteristics of Inclusions in Bearing Steel GCrl5

赵海; 陈列; 严清忠; 李世健; 杨亮; 成国光

您当前的位置：

首页 >

文章列表页 >

Effect of Electro-Slag Remelting on Chemical Composition and Characteristics of Inclusions in Bearing Steel GCrl5

更新时间：2026-01-21

- Effect of Electro-Slag Remelting on Chemical Composition and Characteristics of Inclusions in Bearing Steel GCrl5
- Special Steel Vol. 37, Issue 4, Pages: 44-48(2016)
- 作者机构：
  
  1. 西宁特殊钢股份有限公司,西宁,810005
  2. 北京科技大学钢铁冶金新技术国家重点实验室,北京,100083
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Online First：03 August 2022，
  
  Published：03 August 2016
- 稿件说明：
移动端阅览
赵海, 陈列, 严清忠, et al. Effect of Electro-Slag Remelting on Chemical Composition and Characteristics of Inclusions in Bearing Steel GCrl5[J]. Special Steel, 2016, 37(4): 44-48.
DOI：

赵海, 陈列, 严清忠, et al. Effect of Electro-Slag Remelting on Chemical Composition and Characteristics of Inclusions in Bearing Steel GCrl5[J]. Special Steel, 2016, 37(4): 44-48. DOI：

摘要

对采用（/%）:45CaF

10CaO

40Al

5MgO渣系重熔的2.3t GCr15轴承钢电渣锭轧成的φ26 mm钢材进行了试验和分析。结果表明

电渣重熔后

电渣锭小头Al、Si烧损及增氧较大头更为严重

母材、小头、大头的Si

Ah和O含量（/%）分别为0.24

0.16

0.21;0.025

0.011

0.017和0.001 0

0.003 0

0.002 0。钢中夹杂物主要以Al

Mg-Al-O

Ca-Al-O为主

并含有少量FiN以及以Mg-Al-O为核心

以TiN为外围的复合夹杂物;小头夹杂物总量为16.49个/mm

大头夹杂物总量为14.96个/mm

电渣锭小头以单一Al

夹杂物为主

大头以Mg-AlO

Ca-Al-O夹杂物为主

主要原因是大头Al含量较高

对渣中MgO

CaO的还原程度较高。

Abstract

The test and analysis on φ26 mm round products rolled from 2. 3 t bearing steel GCH5 electroslag ingot remelting with (/% ) : 45CaF

l0CaO

40Al

5MgO slag series are carried out. Results show that after electroslag remelting (ESR) the burning loss of Al and Si and oxygen content increase in top of ingot are larger that that increase in bottom of ingot

the Si

Alt and 0 content in electrode

top and bottom are respectively (/%) 0. 24

0. 16

0. 21 ； 0. 025

0. 011

0. 017 and 0. 001 0

0.003 0

0.002 0. The inclusions in steel are mainly Al

Mg-Al-0 and Ca-Al-0 with minor TiN and compound inclusion with Mg-Al-0 core claddin

g by TiN ； and the per mm

inclusions number in top ingot is 16. 49 and that in bottom ingot is 14. 96; the main inclusion in top of ingot is Al

while that in bottom of ingot is Mg-Al- 0 and Ca-Al-0

the main cause is the Al content in bottom of ingot is higher to increase the reduction of MgO and CaO in slag.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

⁰