Effect of Ti-B Microalloying on Hot Ductility of Casting Bloom of Steel ML20Cr for Cold Heading

您当前的位置：

首页 >

文章列表页 >

Effect of Ti-B Microalloying on Hot Ductility of Casting Bloom of Steel ML20Cr for Cold Heading

更新时间：2026-01-21

- Effect of Ti-B Microalloying on Hot Ductility of Casting Bloom of Steel ML20Cr for Cold Heading
- Special Steel Vol. 38, Issue 2, Pages: 53-55(2017)
- 作者机构：
  
  1. 邢台钢铁有限责任公司,邢台,054027
  2. 河北省线材工程技术研究中心,邢台,054027
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：26 October 2016，
  
  Online First：23 July 2022，
  
  Published：23 July 2017
- 稿件说明：
移动端阅览
李永超, 段路昭, 李宝秀, et al. Effect of Ti-B Microalloying on Hot Ductility of Casting Bloom of Steel ML20Cr for Cold Heading[J]. Special Steel, 2017, 38(2): 53-55.
DOI：

李永超, 段路昭, 李宝秀, et al. Effect of Ti-B Microalloying on Hot Ductility of Casting Bloom of Steel ML20Cr for Cold Heading[J]. Special Steel, 2017, 38(2): 53-55. DOI：

摘要

试验ML20Cr钢280 mm×325 mn连铸坯的生产流程为80t顶底复哄转炉-LF-CC工艺。借助Gleeble 1500热模拟试验机测试了试验钢连铸坯的650~1200℃热塑性曲线.并分析了添加0.029Ti-0.0023B对ML20Cr钢（/%:0.21~0.22C，0.22~0.23Si，0.74~0.76Mn，0.015~0.017P，0.002~0.003S，0.95~0.96Cr，0.034~0.036A1，0.0050~0.0051N）热塑性的影响。结果表明，在650~900℃范围

含0.029Ti-0.0023B的ML20Cr钢的塑性（750℃断面收缩率＞70%）优于不加Ti-B的ML20Cr钢（750℃断面收缩率＜50%）。其主要原因TiN优先析出

降低了细小AlN析出物在第三脆性区的影响，同时B元素在奥氏体晶界偏聚，抑制先共析铁素体薄膜的形成，从而有效改善了钢的热塑性。工业生产结果表明，加微量Ti-B后ML20Cr连铸坯开裂率由3.7%降低到0.3%。

Abstract

The production flowsheet of tested 280 mm x 325 mm casting bloom of steel ML20Cr is 80t top and bottom combined blowing converter-LF-CC process. The hot ductility curves of casting bloom of tested steel at 650~1200 °C are measured by Gleeble 1500 hot simulator

and the effect of adding 0.029Ti-0.0023 B on hot ductility of steel MLCr20 (/% : 0.2i〜0.22C

0.22~0.23Si

0.74〜0.76Mn

0.015~0.017P

0.002〜0.003S

0.95〜0.96Cr

0.034~0.036 Al

0.0050~0.0051N) is analyzed. Results show that in 650~ 900℃ the plasticity of steel ML20Cr containing 0.029Ti-0.0023B ( reduction of area ＞70% at 750℃) is better that of steel ML20Cr un-adding Ti-B ( reduction of area ＜50% at 750°C ). The main reason is that the prior precipitated TiN decreases the effect of fine AIN in No Ⅲ brittle zone

and the B segregate at austenite grain boundary to inhibit the formation of proeutectoid ferrite thin film

in order to effectively improve the hot ductility of steel. The commercial production results show that with adding micro Ti-B tn steel ML20Cr the cracking j-ate of casting bloom decreases from 3.7% to 0.3% .

关键词

Keywords

references

0

Views

0

下载量

0

CSCD

0

CNKI被引量

>

Alert me when the article has been cited

提交

Tools

Publicity Resources

Related Articles

Effect of AlN and Zr Microalloying on Thermoplasticity and Grain Size of Carburized Gear Steel

Hot Deformation Characteristics of Nickel Base Corrosion Resistant Alloy GH536B(G3)

Related Author

Yang Feifei

Xu Haiwei

Gen Hao

Ji Chenxi

Di Guobiao

苏玉华

包耀宗

董瀚

Related Institution

Shougang Research Institute of Technology

Beijing Key Laboratory of Green Recyclable Process for Iron and Steel Production Technology

Beijing Energy Steel Engineering and Technology Research Center Beijing

Shougang Jingtang Iron and Steel United Co.， Ltd.

University of Science and Technology Beijing

⁰