A Study on Water Model for 130 t and 160 t Ladle Furnace (LF)
with Bottom Argon Blowing

Special Steel ›› 2010, Vol. 31 ›› Issue (6): 1-3.

A Study on Water Model for 130 t and 160 t Ladle Furnace (LF) with Bottom Argon Blowing

Wei Jianglin¹, Tang Ping¹, Wen Guanghua¹, Zhu Mingmei¹, Gao Jianjun², Liu Hailan²

1 College of Material Science and Engineering of Chongqing University, Chongqing 400045 ；
2 China Frist Heavy Machine Industries Group Co, Qiqihaer 161042

Received:2010-06-07 Online:2010-12-01 Published:2022-10-27

130t和160t钢包炉(LF)底吹氩的水模拟研究

韦江林¹，唐萍¹，文光华¹，祝明妹¹，高建军²，刘海澜²

1重庆大学材料科学与工程学院，重庆400045 ；
2中国第一重型机械集团公司，齐齐哈尔161042

通讯作者: 唐萍，教授，重庆大学材料科学与工程学院，重庆400045
作者简介:韦江林(1983 -),女，硕士研究生，二次精炼研究。
基金资助:
“十一五”科技重大专项课题资助(2009ZX04014-061)

Abstract

Abstract: Based on similarity theory, the effect of bottom gas blowing rate on flow characteristics of fluid in ladle including mixing time, liquid level fluctuation, bare area diameter and floating time of inclusions has been studied by using 1 : 5 and 1 ： 5.5 model for an 130 t and an 160 t ladle at Frist Heavy Machine Industries. Results show that for 130 t ladle the optimum bottom argon blowing rate (L/min) for heating to smelt flux, desulphurization-deoxidation, alloying and soft blowing are respectively 200, 600, 400 and 150, and for 160 t ladle that are respectively 300, 500, 500 and 200.

摘要： 根据相似原理采用一重130 t、160 t钢包1:5和1:5.5比例的水模型,研究了底吹流量对混匀时间、液面扰动、液面亮圈直径和夹杂物上浮时间等钢包内流体流动特性的影响。结果表明,对130 t钢包加热化渣、脱硫-脱氧、合金化及软吹的最佳吹氩流量(L/min)分别为200、600、400、150;而对160 t钢包则分别为300、500、500、200。

关键词: 钢包炉(LF), 底吹氩, 水模拟

Wei Jianglin, Tang Ping, Wen Guanghua, Zhu Mingmei, Gao Jianjun, Liu Hailan. A Study on Water Model for 130 t and 160 t Ladle Furnace (LF) with Bottom Argon Blowing[J]. Special Steel, 2010, 31(6): 1-3.

韦江林, 唐萍, 文光华, 祝明妹, 高建军, 刘海澜. 130t和160t钢包炉(LF)底吹氩的水模拟研究[J]. 特殊钢, 2010, 31(6): 1-3.