Effect of Primary Recrystallization Annealing on Structure and Texture of Cu-Bearing Hi-B Silicon Steel Produced by Simulating CSP Process

黄明柱; 赵刚; 曹靖威; 陈佳丽; 李海龙; 肖欢

您当前的位置：

首页 >

文章列表页 >

Effect of Primary Recrystallization Annealing on Structure and Texture of Cu-Bearing Hi-B Silicon Steel Produced by Simulating CSP Process

更新时间：2026-01-21

- Effect of Primary Recrystallization Annealing on Structure and Texture of Cu-Bearing Hi-B Silicon Steel Produced by Simulating CSP Process
- Special Steel Vol. 37, Issue 4, Pages: 58-60(2016)
- 作者机构：
  
  武汉科技大学钢铁冶金及资源利用省部共建教育部重点实验室,武汉,430081
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Received：07 March 2016，
  
  Online First：06 August 2022，
  
  Published：06 August 2016
- 稿件说明：
移动端阅览
黄明柱, 赵刚, 曹靖威, et al. Effect of Primary Recrystallization Annealing on Structure and Texture of Cu-Bearing Hi-B Silicon Steel Produced by Simulating CSP Process[J]. Special Steel, 2016, 37(4): 58-60.
DOI：

黄明柱, 赵刚, 曹靖威, et al. Effect of Primary Recrystallization Annealing on Structure and Texture of Cu-Bearing Hi-B Silicon Steel Produced by Simulating CSP Process[J]. Special Steel, 2016, 37(4): 58-60. DOI：

摘要

在实验室用模拟CSP工艺试制Hi-B高磁感取向硅钢薄板（/%:0.07C

3.02Si

0.13Mn

0.020P

0.006S

0.21Cu

0.025Cr

0.016A1

0.004Sn）

该钢经25kg真空感应炉熔炼

铸成41 mm×120 mm板坯-热轧成2mm板-1 120℃常化-冷轧成0.27mm薄板。研究了830~870℃

3~7min退火对再结晶组织和织构的影响。结果表明

0.27mm含Cu Hi-B高磁感取向硅钢板的合适退火工艺为830℃ 5 min

其平均晶粒尺寸为15.6μm

不利织构{111}〈110〉和{001}〈110〉含量较低

有利织构{111}〈112〉分布合理

有利于在二次再结晶退火过程形成良好的高斯组织。

Abstract

The sheet of Hi-B high magnetic induction oriented silicon steel (/% : 0. 07C

3. 02Si

0. 13Mn

0. 020P

0. 006S

0. 21Cu

0. 025Cr

0. 016A1

0. 004Sn) is produced by simulating CSP process in laboratory

the steel is melted by a 25 kg vacuum induction furnace

cast to 41 mm x 120 mm slab

hot-rolled to 2 mm plate

normalized at 1 120℃ and cold rolled to 0. 27 mm sheet. The effect of annealing at 830 ~ 870℃ for 3 ~ 7 min on recrystallized structure and texture of steel has been studied. Results show that the suitable annealing process for 0. 27 mm sheet of Cu-bearing Hi- B high magnetic induction oriented silicon steel is at 850℃ for 5 min

its average grain size is 15. 6 μm

the relative level of adverse texture [111] 〈110〉and {001}〈111〉 is lower and the distribution of favorable texture {111} 〈112〉is reasonable that is available to form favorable Goss texture in secondary recrystallization annealing process.

关键词

Keywords

references

Views

下载量

CSCD

CNKI被引量

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of Hot-Rolled Plate Normalization Process on Structure and Properties of Annealed Cold-Rolled Sheet of Oriented Silicon Steel

Effect of Rare Earth Element on Structure and Magnetic Performance of Cold Rolled Non-Oriented Electrical Steel Products

Effect of Primary Recrystallization Annealing Process on Structure and Texture of 3%Si Oriented Silicon Steel

Effect of Continuous Annealing Temperature on Structure Texture and Mechanical Properties 390 MPa IF Steel

Effect of Cooling Process after Rolling on Structure and Texture of Simulated CSP Hot-Rolled Hi-B Steel Bearing Copper

Related Author

唐刚

鲍思前

王锋

李黎

李方方

光红兵

张文康

辛宪诚

Related Institution

太原钢铁(集团)有限公司技术中心

首钢冷轧薄板有限公司

北京科技大学冶金工程研究院

武汉工程大学邮电与信息工程学院

太原钢铁(集团)有限公司1先进不锈钢材料国家重点实验室

⁰